产品中心

{"items":[{"m":"MDR-3626T-V","t":"标准版电压输出型倾角传感器","d":"双轴测量，精度 0.1°，电压信号输出，适配工业现场姿态监测与调平。","img":"https://www.fleo.cn/uploads/gallery/20261010_6aca04e71e5d8.png","g":"标准版 0.1°","head":"标准版倾角传感器","sub":"电压 / 数字 / MODBUS / 电流四型，精度 0.1°","axis":"双轴","prec":"0.1°","out":"电压输出","app":"适配工业现场姿态监测与调平。","sk":"3626T","single":false,"ovr":"新一代工业级 MEMS 型双轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[["测量范围","±10° / ±30° / ±60° / ±90°（按型号后缀 I0 / I30 / I60 / I90 区分）"],["测量轴","X、Y 轴"],["绝对精度","0.1 °"],["分辨率","0.01 °"],["长期稳定性","< 0.12 °（@25℃）"],["零点温度系数","±0.01 °/°C（-40~85℃）"],["监测频率","100 Hz"],["工作电压","DC 5V 或 DC 9~36V"],["工作电流","45 mA（DC 12V 条件下）"],["通讯接口","默认 MODBUS（RS485），其它可选"],["平均工作时间","≥ 5000 小时/次"],["抗冲击","> 20000g，0.5ms，3 次/轴"],["抗震动","10grms，10~1000Hz"],["绝缘电阻","≥ 100MΩ"],["防水等级","IP67 或 IP68"],["电缆线","默认 4 芯屏蔽电缆线 1.5 米"],["重量","180g（不含包装盒）"]],"wiring":{"header":["线色","序号","RS232","RS485","TTL"],"rows":[["红色","1","VCC","VCC","VCC"],["黑色","2","GND","GND","GND"],["黄色","3","TXD","(A、D+)","TXD"],["绿色","4","RXD","(B、D-)","RXD"]],"note":"出厂默认 4 芯屏蔽电缆线 1.5 米，端子定义以本表为准；接线前请确认供电极性，避免带电插拔。"},"size":{"model":"L90 × W40 × H27 mm","mount":"4×M4 螺孔","note":"不同安装面结构会有对应尺寸版本，下单前请与技术人员确认孔位与结构版本。"},"mount":["被测量安装面必须平整，安装面不平会导致测量数据不准确。","安装传感器时，轴 A 应与被测角度旋转轴线平行，否则会带来测量误差。","水平向上/向下、竖直向上/向下共四种安装姿态，需对应确认 X/Y 轴正负方向，装反会导致读数符号相反。","安装完成后建议先用标准角度校验一次，确认读数方向与量程符合预期再接入系统。"],"proto":{"summary":"默认 MODBUS RTU（RS485）通讯协议，8 位数据位、1 位停止位、无校验，默认波特率 9600。","rows":[["数据格式","8 位数据位，1 位停止位，无校验，默认速率 9600"],["角度读取功能码","0x03 读（0x06 写）"],["X 轴角度寄存器","0x0001（数量 2，32 位浮点，IEEE754）"],["Y 轴角度寄存器","0x0002（数量 2，32 位浮点，IEEE754）"],["X/Y 双轴寄存器","0x0001（数量 4，一次读回 X+Y）"],["相对/绝对零点","0x000B（0x0000 绝对零点，0x0001 相对零点）"],["通讯速率设置","0x000C（0x0001=2400，0x0002=4800，0x0003=9600，0x0004=19200，0x0000=115200）"],["模块地址设置","0x000D（出厂默认 0x01，总线地址范围 00~FE）"],["掉电保存","update flash 写入 0x000F；参数设置后未发保存命令，断电重启将丢失"]],"notes":["本传感器将两帧数据帧之间的时间间隔提高到大于 10ms，请在每帧数据之间至少留下 10ms 间隔。","通讯时序：主机发送命令 → 10ms 空闲 → 从机回命令 → 10ms 空闲 → 主机发送命令。","如需在 Modbus 协议规定的 3.5 个字节时间内完成收发，请将通讯速率提高到 115200。","修改通讯速率或模块地址后，应立即发送掉电保存指令，否则重新上电后设置会丢失。"]}},{"m":"MDR-3626T-D","t":"标准版数字型倾角传感器","d":"双轴测量，精度 0.1°，数字输出，便于直接接入采集系统。","img":"https://www.fleo.cn/uploads/gallery/20261010_6aca04e71fb5e.png","g":"标准版 0.1°","head":"标准版倾角传感器","sub":"电压 / 数字 / MODBUS / 电流四型，精度 0.1°","axis":"双轴","prec":"0.1°","out":"数字输出","app":"","sk":"3626T","single":false,"ovr":"新一代工业级 MEMS 型双轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[["测量范围","±10° / ±30° / ±60° / ±90°（按型号后缀 I0 / I30 / I60 / I90 区分）"],["测量轴","X、Y 轴"],["绝对精度","0.1 °"],["分辨率","0.01 °"],["长期稳定性","< 0.12 °（@25℃）"],["零点温度系数","±0.01 °/°C（-40~85℃）"],["监测频率","100 Hz"],["工作电压","DC 5V 或 DC 9~36V"],["工作电流","45 mA（DC 12V 条件下）"],["通讯接口","默认 MODBUS（RS485），其它可选"],["平均工作时间","≥ 5000 小时/次"],["抗冲击","> 20000g，0.5ms，3 次/轴"],["抗震动","10grms，10~1000Hz"],["绝缘电阻","≥ 100MΩ"],["防水等级","IP67 或 IP68"],["电缆线","默认 4 芯屏蔽电缆线 1.5 米"],["重量","180g（不含包装盒）"]],"wiring":{"header":["线色","序号","RS232","RS485","TTL"],"rows":[["红色","1","VCC","VCC","VCC"],["黑色","2","GND","GND","GND"],["黄色","3","TXD","(A、D+)","TXD"],["绿色","4","RXD","(B、D-)","RXD"]],"note":"出厂默认 4 芯屏蔽电缆线 1.5 米，端子定义以本表为准；接线前请确认供电极性，避免带电插拔。"},"size":{"model":"L90 × W40 × H27 mm","mount":"4×M4 螺孔","note":"不同安装面结构会有对应尺寸版本，下单前请与技术人员确认孔位与结构版本。"},"mount":["被测量安装面必须平整，安装面不平会导致测量数据不准确。","安装传感器时，轴 A 应与被测角度旋转轴线平行，否则会带来测量误差。","水平向上/向下、竖直向上/向下共四种安装姿态，需对应确认 X/Y 轴正负方向，装反会导致读数符号相反。","安装完成后建议先用标准角度校验一次，确认读数方向与量程符合预期再接入系统。"],"proto":{"summary":"默认 MODBUS RTU（RS485）通讯协议，8 位数据位、1 位停止位、无校验，默认波特率 9600。","rows":[["数据格式","8 位数据位，1 位停止位，无校验，默认速率 9600"],["角度读取功能码","0x03 读（0x06 写）"],["X 轴角度寄存器","0x0001（数量 2，32 位浮点，IEEE754）"],["Y 轴角度寄存器","0x0002（数量 2，32 位浮点，IEEE754）"],["X/Y 双轴寄存器","0x0001（数量 4，一次读回 X+Y）"],["相对/绝对零点","0x000B（0x0000 绝对零点，0x0001 相对零点）"],["通讯速率设置","0x000C（0x0001=2400，0x0002=4800，0x0003=9600，0x0004=19200，0x0000=115200）"],["模块地址设置","0x000D（出厂默认 0x01，总线地址范围 00~FE）"],["掉电保存","update flash 写入 0x000F；参数设置后未发保存命令，断电重启将丢失"]],"notes":["本传感器将两帧数据帧之间的时间间隔提高到大于 10ms，请在每帧数据之间至少留下 10ms 间隔。","通讯时序：主机发送命令 → 10ms 空闲 → 从机回命令 → 10ms 空闲 → 主机发送命令。","如需在 Modbus 协议规定的 3.5 个字节时间内完成收发，请将通讯速率提高到 115200。","修改通讯速率或模块地址后，应立即发送掉电保存指令，否则重新上电后设置会丢失。"]}},{"m":"MDR-3626T-M","t":"标准版 MODBUS 型倾角传感器","d":"双轴测量，精度 0.1°，支持 Modbus-RTU 协议，利于多节点组网。","img":"https://www.fleo.cn/uploads/gallery/20261010_6aca04e720ab5.png","g":"标准版 0.1°","head":"标准版倾角传感器","sub":"电压 / 数字 / MODBUS / 电流四型，精度 0.1°","axis":"双轴","prec":"0.1°","out":"Modbus-RTU 协议","app":"","sk":"3626T","single":false,"ovr":"新一代工业级 MEMS 型双轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[["测量范围","±10° / ±30° / ±60° / ±90°（按型号后缀 I0 / I30 / I60 / I90 区分）"],["测量轴","X、Y 轴"],["绝对精度","0.1 °"],["分辨率","0.01 °"],["长期稳定性","< 0.12 °（@25℃）"],["零点温度系数","±0.01 °/°C（-40~85℃）"],["监测频率","100 Hz"],["工作电压","DC 5V 或 DC 9~36V"],["工作电流","45 mA（DC 12V 条件下）"],["通讯接口","默认 MODBUS（RS485），其它可选"],["平均工作时间","≥ 5000 小时/次"],["抗冲击","> 20000g，0.5ms，3 次/轴"],["抗震动","10grms，10~1000Hz"],["绝缘电阻","≥ 100MΩ"],["防水等级","IP67 或 IP68"],["电缆线","默认 4 芯屏蔽电缆线 1.5 米"],["重量","180g（不含包装盒）"]],"wiring":{"header":["线色","序号","RS232","RS485","TTL"],"rows":[["红色","1","VCC","VCC","VCC"],["黑色","2","GND","GND","GND"],["黄色","3","TXD","(A、D+)","TXD"],["绿色","4","RXD","(B、D-)","RXD"]],"note":"出厂默认 4 芯屏蔽电缆线 1.5 米，端子定义以本表为准；接线前请确认供电极性，避免带电插拔。"},"size":{"model":"L90 × W40 × H27 mm","mount":"4×M4 螺孔","note":"不同安装面结构会有对应尺寸版本，下单前请与技术人员确认孔位与结构版本。"},"mount":["被测量安装面必须平整，安装面不平会导致测量数据不准确。","安装传感器时，轴 A 应与被测角度旋转轴线平行，否则会带来测量误差。","水平向上/向下、竖直向上/向下共四种安装姿态，需对应确认 X/Y 轴正负方向，装反会导致读数符号相反。","安装完成后建议先用标准角度校验一次，确认读数方向与量程符合预期再接入系统。"],"proto":{"summary":"默认 MODBUS RTU（RS485）通讯协议，8 位数据位、1 位停止位、无校验，默认波特率 9600。","rows":[["数据格式","8 位数据位，1 位停止位，无校验，默认速率 9600"],["角度读取功能码","0x03 读（0x06 写）"],["X 轴角度寄存器","0x0001（数量 2，32 位浮点，IEEE754）"],["Y 轴角度寄存器","0x0002（数量 2，32 位浮点，IEEE754）"],["X/Y 双轴寄存器","0x0001（数量 4，一次读回 X+Y）"],["相对/绝对零点","0x000B（0x0000 绝对零点，0x0001 相对零点）"],["通讯速率设置","0x000C（0x0001=2400，0x0002=4800，0x0003=9600，0x0004=19200，0x0000=115200）"],["模块地址设置","0x000D（出厂默认 0x01，总线地址范围 00~FE）"],["掉电保存","update flash 写入 0x000F；参数设置后未发保存命令，断电重启将丢失"]],"notes":["本传感器将两帧数据帧之间的时间间隔提高到大于 10ms，请在每帧数据之间至少留下 10ms 间隔。","通讯时序：主机发送命令 → 10ms 空闲 → 从机回命令 → 10ms 空闲 → 主机发送命令。","如需在 Modbus 协议规定的 3.5 个字节时间内完成收发，请将通讯速率提高到 115200。","修改通讯速率或模块地址后，应立即发送掉电保存指令，否则重新上电后设置会丢失。"]}},{"m":"MDR-3626T-I","t":"标准版电流输出型倾角传感器","d":"双轴测量，精度 0.1°，4-20mA 电流输出，兼容老旧仪表柜。","img":"https://www.fleo.cn/uploads/gallery/20261010_6aca04e721b6a.png","g":"标准版 0.1°","head":"标准版倾角传感器","sub":"电压 / 数字 / MODBUS / 电流四型，精度 0.1°","axis":"双轴","prec":"0.1°","out":"4-20mA 电流输出","app":"","sk":"3626T","single":false,"ovr":"新一代工业级 MEMS 型双轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[["测量范围","±10° / ±30° / ±60° / ±90°（按型号后缀 I0 / I30 / I60 / I90 区分）"],["测量轴","X、Y 轴"],["绝对精度","0.1 °"],["分辨率","0.01 °"],["长期稳定性","< 0.12 °（@25℃）"],["零点温度系数","±0.01 °/°C（-40~85℃）"],["监测频率","100 Hz"],["工作电压","DC 5V 或 DC 9~36V"],["工作电流","45 mA（DC 12V 条件下）"],["通讯接口","默认 MODBUS（RS485），其它可选"],["平均工作时间","≥ 5000 小时/次"],["抗冲击","> 20000g，0.5ms，3 次/轴"],["抗震动","10grms，10~1000Hz"],["绝缘电阻","≥ 100MΩ"],["防水等级","IP67 或 IP68"],["电缆线","默认 4 芯屏蔽电缆线 1.5 米"],["重量","180g（不含包装盒）"]],"wiring":{"header":["线色","序号","RS232","RS485","TTL"],"rows":[["红色","1","VCC","VCC","VCC"],["黑色","2","GND","GND","GND"],["黄色","3","TXD","(A、D+)","TXD"],["绿色","4","RXD","(B、D-)","RXD"]],"note":"出厂默认 4 芯屏蔽电缆线 1.5 米，端子定义以本表为准；接线前请确认供电极性，避免带电插拔。"},"size":{"model":"L90 × W40 × H27 mm","mount":"4×M4 螺孔","note":"不同安装面结构会有对应尺寸版本，下单前请与技术人员确认孔位与结构版本。"},"mount":["被测量安装面必须平整，安装面不平会导致测量数据不准确。","安装传感器时，轴 A 应与被测角度旋转轴线平行，否则会带来测量误差。","水平向上/向下、竖直向上/向下共四种安装姿态，需对应确认 X/Y 轴正负方向，装反会导致读数符号相反。","安装完成后建议先用标准角度校验一次，确认读数方向与量程符合预期再接入系统。"],"proto":{"summary":"默认 MODBUS RTU（RS485）通讯协议，8 位数据位、1 位停止位、无校验，默认波特率 9600。","rows":[["数据格式","8 位数据位，1 位停止位，无校验，默认速率 9600"],["角度读取功能码","0x03 读（0x06 写）"],["X 轴角度寄存器","0x0001（数量 2，32 位浮点，IEEE754）"],["Y 轴角度寄存器","0x0002（数量 2，32 位浮点，IEEE754）"],["X/Y 双轴寄存器","0x0001（数量 4，一次读回 X+Y）"],["相对/绝对零点","0x000B（0x0000 绝对零点，0x0001 相对零点）"],["通讯速率设置","0x000C（0x0001=2400，0x0002=4800，0x0003=9600，0x0004=19200，0x0000=115200）"],["模块地址设置","0x000D（出厂默认 0x01，总线地址范围 00~FE）"],["掉电保存","update flash 写入 0x000F；参数设置后未发保存命令，断电重启将丢失"]],"notes":["本传感器将两帧数据帧之间的时间间隔提高到大于 10ms，请在每帧数据之间至少留下 10ms 间隔。","通讯时序：主机发送命令 → 10ms 空闲 → 从机回命令 → 10ms 空闲 → 主机发送命令。","如需在 Modbus 协议规定的 3.5 个字节时间内完成收发，请将通讯速率提高到 115200。","修改通讯速率或模块地址后，应立即发送掉电保存指令，否则重新上电后设置会丢失。"]}},{"m":"MDR-3616T-V","t":"标准版电压输出型倾角传感器（单轴）","d":"单轴测量，精度 0.1°，电压输出，适合单向倾斜监测与校正。","img":"https://www.fleo.cn/uploads/gallery/20261010_6aca04e722f13.png","g":"标准版 0.1°","head":"标准版倾角传感器","sub":"电压 / 数字 / MODBUS / 电流四型，精度 0.1°","axis":"单轴","prec":"0.1°","out":"电压输出","app":"适合单向倾斜监测与校正。","sk":"3626T","single":true,"ovr":"新一代工业级 MEMS 型单轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[["测量范围","±10° / ±30° / ±60° / ±90°（按型号后缀 I0 / I30 / I60 / I90 区分）"],["测量轴","X 轴（单轴测量）"],["绝对精度","0.1 °"],["分辨率","0.01 °"],["长期稳定性","< 0.12 °（@25℃）"],["零点温度系数","±0.01 °/°C（-40~85℃）"],["监测频率","100 Hz"],["工作电压","DC 5V 或 DC 9~36V"],["工作电流","45 mA（DC 12V 条件下）"],["通讯接口","默认 MODBUS（RS485），其它可选"],["平均工作时间","≥ 5000 小时/次"],["抗冲击","> 20000g，0.5ms，3 次/轴"],["抗震动","10grms，10~1000Hz"],["绝缘电阻","≥ 100MΩ"],["防水等级","IP67 或 IP68"],["电缆线","默认 4 芯屏蔽电缆线 1.5 米"],["重量","180g（不含包装盒）"]],"wiring":{"header":["线色","序号","RS232","RS485","TTL"],"rows":[["红色","1","VCC","VCC","VCC"],["黑色","2","GND","GND","GND"],["黄色","3","TXD","(A、D+)","TXD"],["绿色","4","RXD","(B、D-)","RXD"]],"note":"出厂默认 4 芯屏蔽电缆线 1.5 米，端子定义以本表为准；接线前请确认供电极性，避免带电插拔。"},"size":{"model":"L90 × W40 × H27 mm","mount":"4×M4 螺孔","note":"不同安装面结构会有对应尺寸版本，下单前请与技术人员确认孔位与结构版本。"},"mount":["被测量安装面必须平整，安装面不平会导致测量数据不准确。","安装传感器时，轴 A 应与被测角度旋转轴线平行，否则会带来测量误差。","水平向上/向下、竖直向上/向下共四种安装姿态，需对应确认 X/Y 轴正负方向，装反会导致读数符号相反。","安装完成后建议先用标准角度校验一次，确认读数方向与量程符合预期再接入系统。"],"proto":null},{"m":"MDR-3616T-D","t":"标准版数字型倾角传感器（单轴）","d":"单轴测量，精度 0.1°，数字输出，便于接入采集系统。","img":"https://www.fleo.cn/uploads/gallery/20261010_6aca04e71e5d8.png","g":"标准版 0.1°","head":"标准版倾角传感器","sub":"电压 / 数字 / MODBUS / 电流四型，精度 0.1°","axis":"单轴","prec":"0.1°","out":"数字输出","app":"","sk":"3626T","single":true,"ovr":"新一代工业级 MEMS 型单轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[["测量范围","±10° / ±30° / ±60° / ±90°（按型号后缀 I0 / I30 / I60 / I90 区分）"],["测量轴","X 轴（单轴测量）"],["绝对精度","0.1 °"],["分辨率","0.01 °"],["长期稳定性","< 0.12 °（@25℃）"],["零点温度系数","±0.01 °/°C（-40~85℃）"],["监测频率","100 Hz"],["工作电压","DC 5V 或 DC 9~36V"],["工作电流","45 mA（DC 12V 条件下）"],["通讯接口","默认 MODBUS（RS485），其它可选"],["平均工作时间","≥ 5000 小时/次"],["抗冲击","> 20000g，0.5ms，3 次/轴"],["抗震动","10grms，10~1000Hz"],["绝缘电阻","≥ 100MΩ"],["防水等级","IP67 或 IP68"],["电缆线","默认 4 芯屏蔽电缆线 1.5 米"],["重量","180g（不含包装盒）"]],"wiring":{"header":["线色","序号","RS232","RS485","TTL"],"rows":[["红色","1","VCC","VCC","VCC"],["黑色","2","GND","GND","GND"],["黄色","3","TXD","(A、D+)","TXD"],["绿色","4","RXD","(B、D-)","RXD"]],"note":"出厂默认 4 芯屏蔽电缆线 1.5 米，端子定义以本表为准；接线前请确认供电极性，避免带电插拔。"},"size":{"model":"L90 × W40 × H27 mm","mount":"4×M4 螺孔","note":"不同安装面结构会有对应尺寸版本，下单前请与技术人员确认孔位与结构版本。"},"mount":["被测量安装面必须平整，安装面不平会导致测量数据不准确。","安装传感器时，轴 A 应与被测角度旋转轴线平行，否则会带来测量误差。","水平向上/向下、竖直向上/向下共四种安装姿态，需对应确认 X/Y 轴正负方向，装反会导致读数符号相反。","安装完成后建议先用标准角度校验一次，确认读数方向与量程符合预期再接入系统。"],"proto":null},{"m":"MDR-3616T-M","t":"标准版 MODBUS 型倾角传感器（单轴）","d":"单轴测量，精度 0.1°，支持 Modbus-RTU 协议。","img":"https://www.fleo.cn/uploads/gallery/20261010_6aca04e71fb5e.png","g":"标准版 0.1°","head":"标准版倾角传感器","sub":"电压 / 数字 / MODBUS / 电流四型，精度 0.1°","axis":"单轴","prec":"0.1°","out":"Modbus-RTU 协议","app":"","sk":"3626T","single":true,"ovr":"新一代工业级 MEMS 型单轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[["测量范围","±10° / ±30° / ±60° / ±90°（按型号后缀 I0 / I30 / I60 / I90 区分）"],["测量轴","X 轴（单轴测量）"],["绝对精度","0.1 °"],["分辨率","0.01 °"],["长期稳定性","< 0.12 °（@25℃）"],["零点温度系数","±0.01 °/°C（-40~85℃）"],["监测频率","100 Hz"],["工作电压","DC 5V 或 DC 9~36V"],["工作电流","45 mA（DC 12V 条件下）"],["通讯接口","默认 MODBUS（RS485），其它可选"],["平均工作时间","≥ 5000 小时/次"],["抗冲击","> 20000g，0.5ms，3 次/轴"],["抗震动","10grms，10~1000Hz"],["绝缘电阻","≥ 100MΩ"],["防水等级","IP67 或 IP68"],["电缆线","默认 4 芯屏蔽电缆线 1.5 米"],["重量","180g（不含包装盒）"]],"wiring":{"header":["线色","序号","RS232","RS485","TTL"],"rows":[["红色","1","VCC","VCC","VCC"],["黑色","2","GND","GND","GND"],["黄色","3","TXD","(A、D+)","TXD"],["绿色","4","RXD","(B、D-)","RXD"]],"note":"出厂默认 4 芯屏蔽电缆线 1.5 米，端子定义以本表为准；接线前请确认供电极性，避免带电插拔。"},"size":{"model":"L90 × W40 × H27 mm","mount":"4×M4 螺孔","note":"不同安装面结构会有对应尺寸版本，下单前请与技术人员确认孔位与结构版本。"},"mount":["被测量安装面必须平整，安装面不平会导致测量数据不准确。","安装传感器时，轴 A 应与被测角度旋转轴线平行，否则会带来测量误差。","水平向上/向下、竖直向上/向下共四种安装姿态，需对应确认 X/Y 轴正负方向，装反会导致读数符号相反。","安装完成后建议先用标准角度校验一次，确认读数方向与量程符合预期再接入系统。"],"proto":null},{"m":"MDR-3616T-I","t":"标准版电流输出型倾角传感器（单轴）","d":"单轴测量，精度 0.1°，4-20mA 电流输出。","img":"https://www.fleo.cn/uploads/gallery/20261010_6aca04e720ab5.png","g":"标准版 0.1°","head":"标准版倾角传感器","sub":"电压 / 数字 / MODBUS / 电流四型，精度 0.1°","axis":"单轴","prec":"0.1°","out":"4-20mA 电流输出","app":"","sk":"3626T","single":true,"ovr":"新一代工业级 MEMS 型单轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[["测量范围","±10° / ±30° / ±60° / ±90°（按型号后缀 I0 / I30 / I60 / I90 区分）"],["测量轴","X 轴（单轴测量）"],["绝对精度","0.1 °"],["分辨率","0.01 °"],["长期稳定性","< 0.12 °（@25℃）"],["零点温度系数","±0.01 °/°C（-40~85℃）"],["监测频率","100 Hz"],["工作电压","DC 5V 或 DC 9~36V"],["工作电流","45 mA（DC 12V 条件下）"],["通讯接口","默认 MODBUS（RS485），其它可选"],["平均工作时间","≥ 5000 小时/次"],["抗冲击","> 20000g，0.5ms，3 次/轴"],["抗震动","10grms，10~1000Hz"],["绝缘电阻","≥ 100MΩ"],["防水等级","IP67 或 IP68"],["电缆线","默认 4 芯屏蔽电缆线 1.5 米"],["重量","180g（不含包装盒）"]],"wiring":{"header":["线色","序号","RS232","RS485","TTL"],"rows":[["红色","1","VCC","VCC","VCC"],["黑色","2","GND","GND","GND"],["黄色","3","TXD","(A、D+)","TXD"],["绿色","4","RXD","(B、D-)","RXD"]],"note":"出厂默认 4 芯屏蔽电缆线 1.5 米，端子定义以本表为准；接线前请确认供电极性，避免带电插拔。"},"size":{"model":"L90 × W40 × H27 mm","mount":"4×M4 螺孔","note":"不同安装面结构会有对应尺寸版本，下单前请与技术人员确认孔位与结构版本。"},"mount":["被测量安装面必须平整，安装面不平会导致测量数据不准确。","安装传感器时，轴 A 应与被测角度旋转轴线平行，否则会带来测量误差。","水平向上/向下、竖直向上/向下共四种安装姿态，需对应确认 X/Y 轴正负方向，装反会导致读数符号相反。","安装完成后建议先用标准角度校验一次，确认读数方向与量程符合预期再接入系统。"],"proto":null},{"m":"MDR-3627T-V","t":"中精度电压输出型倾角传感器","d":"双轴测量，精度 0.01°，电压输出，适用于边坡与挡墙监测。","img":"https://www.fleo.cn/uploads/gallery/20261010_6aca04e721b6a.png","g":"中精度 0.01°","head":"中精度倾角传感器","sub":"精度 0.01°，双轴 / 单轴可选","axis":"双轴","prec":"0.01°","out":"电压输出","app":"适用于边坡与挡墙监测。","sk":"3627T","single":false,"ovr":"新一代工业级 MEMS 型双轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[["测量范围","±10° / ±30° / ±60° / ±90°（按型号后缀 I0 / I30 / I60 / I90 区分）"],["测量轴","X、Y 轴"],["绝对精度","0.01 °（±10° / ±30° 量程）；0.02 °（±60° / ±90° 量程）"],["分辨率","0.001 °"],["长期稳定性","< 0.012 °（@25℃）"],["零点温度系数","±0.008 °/°C（-40~85℃）"],["监测频率","100 Hz"],["工作电压","DC 5V 或 DC 9~36V"],["工作电流","45 mA（DC 12V 条件下）"],["通讯接口","默认 MODBUS（RS485），其它可选"],["平均工作时间","≥ 5000 小时/次"],["抗冲击","> 20000g，0.5ms，3 次/轴"],["抗震动","10grms，10~1000Hz"],["绝缘电阻","≥ 100MΩ"],["防水等级","IP67 或 IP68"],["电缆线","默认 4 芯屏蔽电缆线 1.5 米"],["重量","180g（不含包装盒）"]],"wiring":{"header":["线色","序号","RS232","RS485","TTL"],"rows":[["红色","1","VCC","VCC","VCC"],["黑色","2","GND","GND","GND"],["黄色","3","TXD","(A、D+)","TXD"],["绿色","4","RXD","(B、D-)","RXD"]],"note":"出厂默认 4 芯屏蔽电缆线 1.5 米，端子定义以本表为准；接线前请确认供电极性，避免带电插拔。"},"size":{"model":"L90 × W40 × H27 mm","mount":"4×M4 螺孔","note":"不同安装面结构会有对应尺寸版本，下单前请与技术人员确认孔位与结构版本。"},"mount":["被测量安装面必须平整，安装面不平会导致测量数据不准确。","安装传感器时，轴 A 应与被测角度旋转轴线平行，否则会带来测量误差。","水平向上/向下、竖直向上/向下共四种安装姿态，需对应确认 X/Y 轴正负方向，装反会导致读数符号相反。","安装完成后建议先用标准角度校验一次，确认读数方向与量程符合预期再接入系统。"],"proto":{"summary":"默认 MODBUS RTU（RS485）通讯协议，8 位数据位、1 位停止位、无校验，默认波特率 9600。","rows":[["数据格式","8 位数据位，1 位停止位，无校验，默认速率 9600"],["角度读取功能码","0x03 读（0x06 写）"],["X 轴角度寄存器","0x0001（数量 2，32 位浮点，IEEE754）"],["Y 轴角度寄存器","0x0002（数量 2，32 位浮点，IEEE754）"],["X/Y 双轴寄存器","0x0001（数量 4，一次读回 X+Y）"],["相对/绝对零点","0x000B（0x0000 绝对零点，0x0001 相对零点）"],["通讯速率设置","0x000C（0x0001=2400，0x0002=4800，0x0003=9600，0x0004=19200，0x0000=115200）"],["模块地址设置","0x000D（出厂默认 0x01，总线地址范围 00~FE）"],["掉电保存","update flash 写入 0x000F；参数设置后未发保存命令，断电重启将丢失"]],"notes":["本传感器将两帧数据帧之间的时间间隔提高到大于 10ms，请在每帧数据之间至少留下 10ms 间隔。","通讯时序：主机发送命令 → 10ms 空闲 → 从机回命令 → 10ms 空闲 → 主机发送命令。","如需在 Modbus 协议规定的 3.5 个字节时间内完成收发，请将通讯速率提高到 115200。","修改通讯速率或模块地址后，应立即发送掉电保存指令，否则重新上电后设置会丢失。"]}},{"m":"MDR-3627T-D","t":"中精度数字型倾角传感器","d":"双轴测量，精度 0.01°，数字输出，便于接入采集系统。","img":"https://www.fleo.cn/uploads/gallery/20261010_6aca04e722f13.png","g":"中精度 0.01°","head":"中精度倾角传感器","sub":"精度 0.01°，双轴 / 单轴可选","axis":"双轴","prec":"0.01°","out":"数字输出","app":"","sk":"3627T","single":false,"ovr":"新一代工业级 MEMS 型双轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[["测量范围","±10° / ±30° / ±60° / ±90°（按型号后缀 I0 / I30 / I60 / I90 区分）"],["测量轴","X、Y 轴"],["绝对精度","0.01 °（±10° / ±30° 量程）；0.02 °（±60° / ±90° 量程）"],["分辨率","0.001 °"],["长期稳定性","< 0.012 °（@25℃）"],["零点温度系数","±0.008 °/°C（-40~85℃）"],["监测频率","100 Hz"],["工作电压","DC 5V 或 DC 9~36V"],["工作电流","45 mA（DC 12V 条件下）"],["通讯接口","默认 MODBUS（RS485），其它可选"],["平均工作时间","≥ 5000 小时/次"],["抗冲击","> 20000g，0.5ms，3 次/轴"],["抗震动","10grms，10~1000Hz"],["绝缘电阻","≥ 100MΩ"],["防水等级","IP67 或 IP68"],["电缆线","默认 4 芯屏蔽电缆线 1.5 米"],["重量","180g（不含包装盒）"]],"wiring":{"header":["线色","序号","RS232","RS485","TTL"],"rows":[["红色","1","VCC","VCC","VCC"],["黑色","2","GND","GND","GND"],["黄色","3","TXD","(A、D+)","TXD"],["绿色","4","RXD","(B、D-)","RXD"]],"note":"出厂默认 4 芯屏蔽电缆线 1.5 米，端子定义以本表为准；接线前请确认供电极性，避免带电插拔。"},"size":{"model":"L90 × W40 × H27 mm","mount":"4×M4 螺孔","note":"不同安装面结构会有对应尺寸版本，下单前请与技术人员确认孔位与结构版本。"},"mount":["被测量安装面必须平整，安装面不平会导致测量数据不准确。","安装传感器时，轴 A 应与被测角度旋转轴线平行，否则会带来测量误差。","水平向上/向下、竖直向上/向下共四种安装姿态，需对应确认 X/Y 轴正负方向，装反会导致读数符号相反。","安装完成后建议先用标准角度校验一次，确认读数方向与量程符合预期再接入系统。"],"proto":{"summary":"默认 MODBUS RTU（RS485）通讯协议，8 位数据位、1 位停止位、无校验，默认波特率 9600。","rows":[["数据格式","8 位数据位，1 位停止位，无校验，默认速率 9600"],["角度读取功能码","0x03 读（0x06 写）"],["X 轴角度寄存器","0x0001（数量 2，32 位浮点，IEEE754）"],["Y 轴角度寄存器","0x0002（数量 2，32 位浮点，IEEE754）"],["X/Y 双轴寄存器","0x0001（数量 4，一次读回 X+Y）"],["相对/绝对零点","0x000B（0x0000 绝对零点，0x0001 相对零点）"],["通讯速率设置","0x000C（0x0001=2400，0x0002=4800，0x0003=9600，0x0004=19200，0x0000=115200）"],["模块地址设置","0x000D（出厂默认 0x01，总线地址范围 00~FE）"],["掉电保存","update flash 写入 0x000F；参数设置后未发保存命令，断电重启将丢失"]],"notes":["本传感器将两帧数据帧之间的时间间隔提高到大于 10ms，请在每帧数据之间至少留下 10ms 间隔。","通讯时序：主机发送命令 → 10ms 空闲 → 从机回命令 → 10ms 空闲 → 主机发送命令。","如需在 Modbus 协议规定的 3.5 个字节时间内完成收发，请将通讯速率提高到 115200。","修改通讯速率或模块地址后，应立即发送掉电保存指令，否则重新上电后设置会丢失。"]}},{"m":"MDR-3627T-M","t":"中精度 MODBUS 型倾角传感器","d":"双轴测量，精度 0.01°，支持 Modbus-RTU 协议。","img":"https://www.fleo.cn/uploads/gallery/20261010_6aca04e71e5d8.png","g":"中精度 0.01°","head":"中精度倾角传感器","sub":"精度 0.01°，双轴 / 单轴可选","axis":"双轴","prec":"0.01°","out":"Modbus-RTU 协议","app":"","sk":"3627T","single":false,"ovr":"新一代工业级 MEMS 型双轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[["测量范围","±10° / ±30° / ±60° / ±90°（按型号后缀 I0 / I30 / I60 / I90 区分）"],["测量轴","X、Y 轴"],["绝对精度","0.01 °（±10° / ±30° 量程）；0.02 °（±60° / ±90° 量程）"],["分辨率","0.001 °"],["长期稳定性","< 0.012 °（@25℃）"],["零点温度系数","±0.008 °/°C（-40~85℃）"],["监测频率","100 Hz"],["工作电压","DC 5V 或 DC 9~36V"],["工作电流","45 mA（DC 12V 条件下）"],["通讯接口","默认 MODBUS（RS485），其它可选"],["平均工作时间","≥ 5000 小时/次"],["抗冲击","> 20000g，0.5ms，3 次/轴"],["抗震动","10grms，10~1000Hz"],["绝缘电阻","≥ 100MΩ"],["防水等级","IP67 或 IP68"],["电缆线","默认 4 芯屏蔽电缆线 1.5 米"],["重量","180g（不含包装盒）"]],"wiring":{"header":["线色","序号","RS232","RS485","TTL"],"rows":[["红色","1","VCC","VCC","VCC"],["黑色","2","GND","GND","GND"],["黄色","3","TXD","(A、D+)","TXD"],["绿色","4","RXD","(B、D-)","RXD"]],"note":"出厂默认 4 芯屏蔽电缆线 1.5 米，端子定义以本表为准；接线前请确认供电极性，避免带电插拔。"},"size":{"model":"L90 × W40 × H27 mm","mount":"4×M4 螺孔","note":"不同安装面结构会有对应尺寸版本，下单前请与技术人员确认孔位与结构版本。"},"mount":["被测量安装面必须平整，安装面不平会导致测量数据不准确。","安装传感器时，轴 A 应与被测角度旋转轴线平行，否则会带来测量误差。","水平向上/向下、竖直向上/向下共四种安装姿态，需对应确认 X/Y 轴正负方向，装反会导致读数符号相反。","安装完成后建议先用标准角度校验一次，确认读数方向与量程符合预期再接入系统。"],"proto":{"summary":"默认 MODBUS RTU（RS485）通讯协议，8 位数据位、1 位停止位、无校验，默认波特率 9600。","rows":[["数据格式","8 位数据位，1 位停止位，无校验，默认速率 9600"],["角度读取功能码","0x03 读（0x06 写）"],["X 轴角度寄存器","0x0001（数量 2，32 位浮点，IEEE754）"],["Y 轴角度寄存器","0x0002（数量 2，32 位浮点，IEEE754）"],["X/Y 双轴寄存器","0x0001（数量 4，一次读回 X+Y）"],["相对/绝对零点","0x000B（0x0000 绝对零点，0x0001 相对零点）"],["通讯速率设置","0x000C（0x0001=2400，0x0002=4800，0x0003=9600，0x0004=19200，0x0000=115200）"],["模块地址设置","0x000D（出厂默认 0x01，总线地址范围 00~FE）"],["掉电保存","update flash 写入 0x000F；参数设置后未发保存命令，断电重启将丢失"]],"notes":["本传感器将两帧数据帧之间的时间间隔提高到大于 10ms，请在每帧数据之间至少留下 10ms 间隔。","通讯时序：主机发送命令 → 10ms 空闲 → 从机回命令 → 10ms 空闲 → 主机发送命令。","如需在 Modbus 协议规定的 3.5 个字节时间内完成收发，请将通讯速率提高到 115200。","修改通讯速率或模块地址后，应立即发送掉电保存指令，否则重新上电后设置会丢失。"]}},{"m":"MDR-3627T-I","t":"中精度电流输出型倾角传感器","d":"双轴测量，精度 0.01°，4-20mA 电流输出。","img":"https://www.fleo.cn/uploads/gallery/20261010_6aca04e71fb5e.png","g":"中精度 0.01°","head":"中精度倾角传感器","sub":"精度 0.01°，双轴 / 单轴可选","axis":"双轴","prec":"0.01°","out":"4-20mA 电流输出","app":"","sk":"3627T","single":false,"ovr":"新一代工业级 MEMS 型双轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[["测量范围","±10° / ±30° / ±60° / ±90°（按型号后缀 I0 / I30 / I60 / I90 区分）"],["测量轴","X、Y 轴"],["绝对精度","0.01 °（±10° / ±30° 量程）；0.02 °（±60° / ±90° 量程）"],["分辨率","0.001 °"],["长期稳定性","< 0.012 °（@25℃）"],["零点温度系数","±0.008 °/°C（-40~85℃）"],["监测频率","100 Hz"],["工作电压","DC 5V 或 DC 9~36V"],["工作电流","45 mA（DC 12V 条件下）"],["通讯接口","默认 MODBUS（RS485），其它可选"],["平均工作时间","≥ 5000 小时/次"],["抗冲击","> 20000g，0.5ms，3 次/轴"],["抗震动","10grms，10~1000Hz"],["绝缘电阻","≥ 100MΩ"],["防水等级","IP67 或 IP68"],["电缆线","默认 4 芯屏蔽电缆线 1.5 米"],["重量","180g（不含包装盒）"]],"wiring":{"header":["线色","序号","RS232","RS485","TTL"],"rows":[["红色","1","VCC","VCC","VCC"],["黑色","2","GND","GND","GND"],["黄色","3","TXD","(A、D+)","TXD"],["绿色","4","RXD","(B、D-)","RXD"]],"note":"出厂默认 4 芯屏蔽电缆线 1.5 米，端子定义以本表为准；接线前请确认供电极性，避免带电插拔。"},"size":{"model":"L90 × W40 × H27 mm","mount":"4×M4 螺孔","note":"不同安装面结构会有对应尺寸版本，下单前请与技术人员确认孔位与结构版本。"},"mount":["被测量安装面必须平整，安装面不平会导致测量数据不准确。","安装传感器时，轴 A 应与被测角度旋转轴线平行，否则会带来测量误差。","水平向上/向下、竖直向上/向下共四种安装姿态，需对应确认 X/Y 轴正负方向，装反会导致读数符号相反。","安装完成后建议先用标准角度校验一次，确认读数方向与量程符合预期再接入系统。"],"proto":{"summary":"默认 MODBUS RTU（RS485）通讯协议，8 位数据位、1 位停止位、无校验，默认波特率 9600。","rows":[["数据格式","8 位数据位，1 位停止位，无校验，默认速率 9600"],["角度读取功能码","0x03 读（0x06 写）"],["X 轴角度寄存器","0x0001（数量 2，32 位浮点，IEEE754）"],["Y 轴角度寄存器","0x0002（数量 2，32 位浮点，IEEE754）"],["X/Y 双轴寄存器","0x0001（数量 4，一次读回 X+Y）"],["相对/绝对零点","0x000B（0x0000 绝对零点，0x0001 相对零点）"],["通讯速率设置","0x000C（0x0001=2400，0x0002=4800，0x0003=9600，0x0004=19200，0x0000=115200）"],["模块地址设置","0x000D（出厂默认 0x01，总线地址范围 00~FE）"],["掉电保存","update flash 写入 0x000F；参数设置后未发保存命令，断电重启将丢失"]],"notes":["本传感器将两帧数据帧之间的时间间隔提高到大于 10ms，请在每帧数据之间至少留下 10ms 间隔。","通讯时序：主机发送命令 → 10ms 空闲 → 从机回命令 → 10ms 空闲 → 主机发送命令。","如需在 Modbus 协议规定的 3.5 个字节时间内完成收发，请将通讯速率提高到 115200。","修改通讯速率或模块地址后，应立即发送掉电保存指令，否则重新上电后设置会丢失。"]}},{"m":"MDR-3617T-V","t":"中精度电压输出型倾角传感器（单轴）","d":"单轴测量，精度 0.01°，电压输出，适合高精度单向监测。","img":"https://www.fleo.cn/uploads/gallery/20261010_6aca04e720ab5.png","g":"中精度 0.01°","head":"中精度倾角传感器","sub":"精度 0.01°，双轴 / 单轴可选","axis":"单轴","prec":"0.01°","out":"电压输出","app":"适合高精度单向监测。","sk":"3627T","single":true,"ovr":"新一代工业级 MEMS 型单轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[["测量范围","±10° / ±30° / ±60° / ±90°（按型号后缀 I0 / I30 / I60 / I90 区分）"],["测量轴","X 轴（单轴测量）"],["绝对精度","0.01 °（±10° / ±30° 量程）；0.02 °（±60° / ±90° 量程）"],["分辨率","0.001 °"],["长期稳定性","< 0.012 °（@25℃）"],["零点温度系数","±0.008 °/°C（-40~85℃）"],["监测频率","100 Hz"],["工作电压","DC 5V 或 DC 9~36V"],["工作电流","45 mA（DC 12V 条件下）"],["通讯接口","默认 MODBUS（RS485），其它可选"],["平均工作时间","≥ 5000 小时/次"],["抗冲击","> 20000g，0.5ms，3 次/轴"],["抗震动","10grms，10~1000Hz"],["绝缘电阻","≥ 100MΩ"],["防水等级","IP67 或 IP68"],["电缆线","默认 4 芯屏蔽电缆线 1.5 米"],["重量","180g（不含包装盒）"]],"wiring":{"header":["线色","序号","RS232","RS485","TTL"],"rows":[["红色","1","VCC","VCC","VCC"],["黑色","2","GND","GND","GND"],["黄色","3","TXD","(A、D+)","TXD"],["绿色","4","RXD","(B、D-)","RXD"]],"note":"出厂默认 4 芯屏蔽电缆线 1.5 米，端子定义以本表为准；接线前请确认供电极性，避免带电插拔。"},"size":{"model":"L90 × W40 × H27 mm","mount":"4×M4 螺孔","note":"不同安装面结构会有对应尺寸版本，下单前请与技术人员确认孔位与结构版本。"},"mount":["被测量安装面必须平整，安装面不平会导致测量数据不准确。","安装传感器时，轴 A 应与被测角度旋转轴线平行，否则会带来测量误差。","水平向上/向下、竖直向上/向下共四种安装姿态，需对应确认 X/Y 轴正负方向，装反会导致读数符号相反。","安装完成后建议先用标准角度校验一次，确认读数方向与量程符合预期再接入系统。"],"proto":null},{"m":"MDR-3617T-D","t":"中精度数字型倾角传感器（单轴）","d":"单轴测量，精度 0.01°，数字输出，便于接入采集系统。","img":"https://www.fleo.cn/uploads/gallery/20261010_6aca04e721b6a.png","g":"中精度 0.01°","head":"中精度倾角传感器","sub":"精度 0.01°，双轴 / 单轴可选","axis":"单轴","prec":"0.01°","out":"数字输出","app":"","sk":"3627T","single":true,"ovr":"新一代工业级 MEMS 型单轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[["测量范围","±10° / ±30° / ±60° / ±90°（按型号后缀 I0 / I30 / I60 / I90 区分）"],["测量轴","X 轴（单轴测量）"],["绝对精度","0.01 °（±10° / ±30° 量程）；0.02 °（±60° / ±90° 量程）"],["分辨率","0.001 °"],["长期稳定性","< 0.012 °（@25℃）"],["零点温度系数","±0.008 °/°C（-40~85℃）"],["监测频率","100 Hz"],["工作电压","DC 5V 或 DC 9~36V"],["工作电流","45 mA（DC 12V 条件下）"],["通讯接口","默认 MODBUS（RS485），其它可选"],["平均工作时间","≥ 5000 小时/次"],["抗冲击","> 20000g，0.5ms，3 次/轴"],["抗震动","10grms，10~1000Hz"],["绝缘电阻","≥ 100MΩ"],["防水等级","IP67 或 IP68"],["电缆线","默认 4 芯屏蔽电缆线 1.5 米"],["重量","180g（不含包装盒）"]],"wiring":{"header":["线色","序号","RS232","RS485","TTL"],"rows":[["红色","1","VCC","VCC","VCC"],["黑色","2","GND","GND","GND"],["黄色","3","TXD","(A、D+)","TXD"],["绿色","4","RXD","(B、D-)","RXD"]],"note":"出厂默认 4 芯屏蔽电缆线 1.5 米，端子定义以本表为准；接线前请确认供电极性，避免带电插拔。"},"size":{"model":"L90 × W40 × H27 mm","mount":"4×M4 螺孔","note":"不同安装面结构会有对应尺寸版本，下单前请与技术人员确认孔位与结构版本。"},"mount":["被测量安装面必须平整，安装面不平会导致测量数据不准确。","安装传感器时，轴 A 应与被测角度旋转轴线平行，否则会带来测量误差。","水平向上/向下、竖直向上/向下共四种安装姿态，需对应确认 X/Y 轴正负方向，装反会导致读数符号相反。","安装完成后建议先用标准角度校验一次，确认读数方向与量程符合预期再接入系统。"],"proto":null},{"m":"MDR-3617T-M","t":"中精度 MODBUS 型倾角传感器（单轴）","d":"单轴测量，精度 0.01°，支持 Modbus-RTU 协议。","img":"https://www.fleo.cn/uploads/gallery/20261010_6aca04e722f13.png","g":"中精度 0.01°","head":"中精度倾角传感器","sub":"精度 0.01°，双轴 / 单轴可选","axis":"单轴","prec":"0.01°","out":"Modbus-RTU 协议","app":"","sk":"3627T","single":true,"ovr":"新一代工业级 MEMS 型单轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[["测量范围","±10° / ±30° / ±60° / ±90°（按型号后缀 I0 / I30 / I60 / I90 区分）"],["测量轴","X 轴（单轴测量）"],["绝对精度","0.01 °（±10° / ±30° 量程）；0.02 °（±60° / ±90° 量程）"],["分辨率","0.001 °"],["长期稳定性","< 0.012 °（@25℃）"],["零点温度系数","±0.008 °/°C（-40~85℃）"],["监测频率","100 Hz"],["工作电压","DC 5V 或 DC 9~36V"],["工作电流","45 mA（DC 12V 条件下）"],["通讯接口","默认 MODBUS（RS485），其它可选"],["平均工作时间","≥ 5000 小时/次"],["抗冲击","> 20000g，0.5ms，3 次/轴"],["抗震动","10grms，10~1000Hz"],["绝缘电阻","≥ 100MΩ"],["防水等级","IP67 或 IP68"],["电缆线","默认 4 芯屏蔽电缆线 1.5 米"],["重量","180g（不含包装盒）"]],"wiring":{"header":["线色","序号","RS232","RS485","TTL"],"rows":[["红色","1","VCC","VCC","VCC"],["黑色","2","GND","GND","GND"],["黄色","3","TXD","(A、D+)","TXD"],["绿色","4","RXD","(B、D-)","RXD"]],"note":"出厂默认 4 芯屏蔽电缆线 1.5 米，端子定义以本表为准；接线前请确认供电极性，避免带电插拔。"},"size":{"model":"L90 × W40 × H27 mm","mount":"4×M4 螺孔","note":"不同安装面结构会有对应尺寸版本，下单前请与技术人员确认孔位与结构版本。"},"mount":["被测量安装面必须平整，安装面不平会导致测量数据不准确。","安装传感器时，轴 A 应与被测角度旋转轴线平行，否则会带来测量误差。","水平向上/向下、竖直向上/向下共四种安装姿态，需对应确认 X/Y 轴正负方向，装反会导致读数符号相反。","安装完成后建议先用标准角度校验一次，确认读数方向与量程符合预期再接入系统。"],"proto":null},{"m":"MDR-3617T-I","t":"中精度电流输出型倾角传感器（单轴）","d":"单轴测量，精度 0.01°，4-20mA 电流输出。","img":"https://www.fleo.cn/uploads/gallery/20261010_6aca04e71e5d8.png","g":"中精度 0.01°","head":"中精度倾角传感器","sub":"精度 0.01°，双轴 / 单轴可选","axis":"单轴","prec":"0.01°","out":"4-20mA 电流输出","app":"","sk":"3627T","single":true,"ovr":"新一代工业级 MEMS 型单轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[["测量范围","±10° / ±30° / ±60° / ±90°（按型号后缀 I0 / I30 / I60 / I90 区分）"],["测量轴","X 轴（单轴测量）"],["绝对精度","0.01 °（±10° / ±30° 量程）；0.02 °（±60° / ±90° 量程）"],["分辨率","0.001 °"],["长期稳定性","< 0.012 °（@25℃）"],["零点温度系数","±0.008 °/°C（-40~85℃）"],["监测频率","100 Hz"],["工作电压","DC 5V 或 DC 9~36V"],["工作电流","45 mA（DC 12V 条件下）"],["通讯接口","默认 MODBUS（RS485），其它可选"],["平均工作时间","≥ 5000 小时/次"],["抗冲击","> 20000g，0.5ms，3 次/轴"],["抗震动","10grms，10~1000Hz"],["绝缘电阻","≥ 100MΩ"],["防水等级","IP67 或 IP68"],["电缆线","默认 4 芯屏蔽电缆线 1.5 米"],["重量","180g（不含包装盒）"]],"wiring":{"header":["线色","序号","RS232","RS485","TTL"],"rows":[["红色","1","VCC","VCC","VCC"],["黑色","2","GND","GND","GND"],["黄色","3","TXD","(A、D+)","TXD"],["绿色","4","RXD","(B、D-)","RXD"]],"note":"出厂默认 4 芯屏蔽电缆线 1.5 米，端子定义以本表为准；接线前请确认供电极性，避免带电插拔。"},"size":{"model":"L90 × W40 × H27 mm","mount":"4×M4 螺孔","note":"不同安装面结构会有对应尺寸版本，下单前请与技术人员确认孔位与结构版本。"},"mount":["被测量安装面必须平整，安装面不平会导致测量数据不准确。","安装传感器时，轴 A 应与被测角度旋转轴线平行，否则会带来测量误差。","水平向上/向下、竖直向上/向下共四种安装姿态，需对应确认 X/Y 轴正负方向，装反会导致读数符号相反。","安装完成后建议先用标准角度校验一次，确认读数方向与量程符合预期再接入系统。"],"proto":null},{"m":"MDR-3628T-V","t":"高精度电压输出型倾角传感器","d":"双轴测量，精度 0.005°，电压输出，适用于大坝与轨道形变监测。","img":"https://www.fleo.cn/uploads/gallery/20261010_6aca04e71fb5e.png","g":"高精度 0.005°","head":"高精度倾角传感器","sub":"精度 0.005°，严苛场景适用","axis":"双轴","prec":"0.005°","out":"电压输出","app":"适用于大坝与轨道形变监测。","sk":"3628T","single":false,"ovr":"新一代工业级 MEMS 型双轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[["测量范围","±5° / ±10° / ±20° / ±30°（按型号后缀 I5 / I10 / I20 / I30 区分）"],["测量轴","X、Y 轴"],["绝对精度","0.005 °"],["分辨率","0.0007 °"],["长期稳定性","< 0.002 °（@25℃）"],["零点温度系数","±0.0008 °/°C（-40~85℃）"],["监测频率","100 Hz"],["工作电压","DC 5V 或 DC 9~36V"],["工作电流","45 mA（DC 12V 条件下）"],["通讯接口","默认 MODBUS（RS485），其它可选"],["平均工作时间","≥ 5000 小时/次"],["抗冲击","> 20000g，0.5ms，3 次/轴"],["抗震动","10grms，10~1000Hz"],["绝缘电阻","≥ 100MΩ"],["防水等级","IP67 或 IP68"],["电缆线","默认 4 芯屏蔽电缆线 1.5 米"],["重量","180g（不含包装盒）"]],"wiring":{"header":["线色","序号","RS232","RS485","TTL"],"rows":[["红色","1","VCC","VCC","VCC"],["黑色","2","GND","GND","GND"],["黄色","3","TXD","(A、D+)","TXD"],["绿色","4","RXD","(B、D-)","RXD"]],"note":"出厂默认 4 芯屏蔽电缆线 1.5 米，端子定义以本表为准；接线前请确认供电极性，避免带电插拔。"},"size":{"model":"L90 × W40 × H27 mm","mount":"4×M4 螺孔","note":"不同安装面结构会有对应尺寸版本，下单前请与技术人员确认孔位与结构版本。"},"mount":["被测量安装面必须平整，安装面不平会导致测量数据不准确。","安装传感器时，轴 A 应与被测角度旋转轴线平行，否则会带来测量误差。","水平向上/向下、竖直向上/向下共四种安装姿态，需对应确认 X/Y 轴正负方向，装反会导致读数符号相反。","安装完成后建议先用标准角度校验一次，确认读数方向与量程符合预期再接入系统。"],"proto":{"summary":"默认 MODBUS RTU（RS485）通讯协议，8 位数据位、1 位停止位、无校验，默认波特率 9600。","rows":[["数据格式","8 位数据位，1 位停止位，无校验，默认速率 9600"],["角度读取功能码","0x03 读（0x06 写）"],["X 轴角度寄存器","0x0001（数量 2，32 位浮点，IEEE754）"],["Y 轴角度寄存器","0x0002（数量 2，32 位浮点，IEEE754）"],["X/Y 双轴寄存器","0x0001（数量 4，一次读回 X+Y）"],["相对/绝对零点","0x000B（0x0000 绝对零点，0x0001 相对零点）"],["通讯速率设置","0x000C（0x0001=2400，0x0002=4800，0x0003=9600，0x0004=19200，0x0000=115200）"],["模块地址设置","0x000D（出厂默认 0x01，总线地址范围 00~FE）"],["掉电保存","update flash 写入 0x000F；参数设置后未发保存命令，断电重启将丢失"]],"notes":["本传感器将两帧数据帧之间的时间间隔提高到大于 10ms，请在每帧数据之间至少留下 10ms 间隔。","通讯时序：主机发送命令 → 10ms 空闲 → 从机回命令 → 10ms 空闲 → 主机发送命令。","如需在 Modbus 协议规定的 3.5 个字节时间内完成收发，请将通讯速率提高到 115200。","修改通讯速率或模块地址后，应立即发送掉电保存指令，否则重新上电后设置会丢失。"]}},{"m":"MDR-3628T-D","t":"高精度数字型倾角传感器","d":"双轴测量，精度 0.005°，数字输出，便于接入采集系统。","img":"https://www.fleo.cn/uploads/gallery/20261010_6aca04e720ab5.png","g":"高精度 0.005°","head":"高精度倾角传感器","sub":"精度 0.005°，严苛场景适用","axis":"双轴","prec":"0.005°","out":"数字输出","app":"","sk":"3628T","single":false,"ovr":"新一代工业级 MEMS 型双轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[["测量范围","±5° / ±10° / ±20° / ±30°（按型号后缀 I5 / I10 / I20 / I30 区分）"],["测量轴","X、Y 轴"],["绝对精度","0.005 °"],["分辨率","0.0007 °"],["长期稳定性","< 0.002 °（@25℃）"],["零点温度系数","±0.0008 °/°C（-40~85℃）"],["监测频率","100 Hz"],["工作电压","DC 5V 或 DC 9~36V"],["工作电流","45 mA（DC 12V 条件下）"],["通讯接口","默认 MODBUS（RS485），其它可选"],["平均工作时间","≥ 5000 小时/次"],["抗冲击","> 20000g，0.5ms，3 次/轴"],["抗震动","10grms，10~1000Hz"],["绝缘电阻","≥ 100MΩ"],["防水等级","IP67 或 IP68"],["电缆线","默认 4 芯屏蔽电缆线 1.5 米"],["重量","180g（不含包装盒）"]],"wiring":{"header":["线色","序号","RS232","RS485","TTL"],"rows":[["红色","1","VCC","VCC","VCC"],["黑色","2","GND","GND","GND"],["黄色","3","TXD","(A、D+)","TXD"],["绿色","4","RXD","(B、D-)","RXD"]],"note":"出厂默认 4 芯屏蔽电缆线 1.5 米，端子定义以本表为准；接线前请确认供电极性，避免带电插拔。"},"size":{"model":"L90 × W40 × H27 mm","mount":"4×M4 螺孔","note":"不同安装面结构会有对应尺寸版本，下单前请与技术人员确认孔位与结构版本。"},"mount":["被测量安装面必须平整，安装面不平会导致测量数据不准确。","安装传感器时，轴 A 应与被测角度旋转轴线平行，否则会带来测量误差。","水平向上/向下、竖直向上/向下共四种安装姿态，需对应确认 X/Y 轴正负方向，装反会导致读数符号相反。","安装完成后建议先用标准角度校验一次，确认读数方向与量程符合预期再接入系统。"],"proto":{"summary":"默认 MODBUS RTU（RS485）通讯协议，8 位数据位、1 位停止位、无校验，默认波特率 9600。","rows":[["数据格式","8 位数据位，1 位停止位，无校验，默认速率 9600"],["角度读取功能码","0x03 读（0x06 写）"],["X 轴角度寄存器","0x0001（数量 2，32 位浮点，IEEE754）"],["Y 轴角度寄存器","0x0002（数量 2，32 位浮点，IEEE754）"],["X/Y 双轴寄存器","0x0001（数量 4，一次读回 X+Y）"],["相对/绝对零点","0x000B（0x0000 绝对零点，0x0001 相对零点）"],["通讯速率设置","0x000C（0x0001=2400，0x0002=4800，0x0003=9600，0x0004=19200，0x0000=115200）"],["模块地址设置","0x000D（出厂默认 0x01，总线地址范围 00~FE）"],["掉电保存","update flash 写入 0x000F；参数设置后未发保存命令，断电重启将丢失"]],"notes":["本传感器将两帧数据帧之间的时间间隔提高到大于 10ms，请在每帧数据之间至少留下 10ms 间隔。","通讯时序：主机发送命令 → 10ms 空闲 → 从机回命令 → 10ms 空闲 → 主机发送命令。","如需在 Modbus 协议规定的 3.5 个字节时间内完成收发，请将通讯速率提高到 115200。","修改通讯速率或模块地址后，应立即发送掉电保存指令，否则重新上电后设置会丢失。"]}},{"m":"MDR-3628T-M","t":"高精度 MODBUS 型倾角传感器","d":"双轴测量，精度 0.005°，支持 Modbus-RTU 协议。","img":"https://www.fleo.cn/uploads/gallery/20261010_6aca04e721b6a.png","g":"高精度 0.005°","head":"高精度倾角传感器","sub":"精度 0.005°，严苛场景适用","axis":"双轴","prec":"0.005°","out":"Modbus-RTU 协议","app":"","sk":"3628T","single":false,"ovr":"新一代工业级 MEMS 型双轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[["测量范围","±5° / ±10° / ±20° / ±30°（按型号后缀 I5 / I10 / I20 / I30 区分）"],["测量轴","X、Y 轴"],["绝对精度","0.005 °"],["分辨率","0.0007 °"],["长期稳定性","< 0.002 °（@25℃）"],["零点温度系数","±0.0008 °/°C（-40~85℃）"],["监测频率","100 Hz"],["工作电压","DC 5V 或 DC 9~36V"],["工作电流","45 mA（DC 12V 条件下）"],["通讯接口","默认 MODBUS（RS485），其它可选"],["平均工作时间","≥ 5000 小时/次"],["抗冲击","> 20000g，0.5ms，3 次/轴"],["抗震动","10grms，10~1000Hz"],["绝缘电阻","≥ 100MΩ"],["防水等级","IP67 或 IP68"],["电缆线","默认 4 芯屏蔽电缆线 1.5 米"],["重量","180g（不含包装盒）"]],"wiring":{"header":["线色","序号","RS232","RS485","TTL"],"rows":[["红色","1","VCC","VCC","VCC"],["黑色","2","GND","GND","GND"],["黄色","3","TXD","(A、D+)","TXD"],["绿色","4","RXD","(B、D-)","RXD"]],"note":"出厂默认 4 芯屏蔽电缆线 1.5 米，端子定义以本表为准；接线前请确认供电极性，避免带电插拔。"},"size":{"model":"L90 × W40 × H27 mm","mount":"4×M4 螺孔","note":"不同安装面结构会有对应尺寸版本，下单前请与技术人员确认孔位与结构版本。"},"mount":["被测量安装面必须平整，安装面不平会导致测量数据不准确。","安装传感器时，轴 A 应与被测角度旋转轴线平行，否则会带来测量误差。","水平向上/向下、竖直向上/向下共四种安装姿态，需对应确认 X/Y 轴正负方向，装反会导致读数符号相反。","安装完成后建议先用标准角度校验一次，确认读数方向与量程符合预期再接入系统。"],"proto":{"summary":"默认 MODBUS RTU（RS485）通讯协议，8 位数据位、1 位停止位、无校验，默认波特率 9600。","rows":[["数据格式","8 位数据位，1 位停止位，无校验，默认速率 9600"],["角度读取功能码","0x03 读（0x06 写）"],["X 轴角度寄存器","0x0001（数量 2，32 位浮点，IEEE754）"],["Y 轴角度寄存器","0x0002（数量 2，32 位浮点，IEEE754）"],["X/Y 双轴寄存器","0x0001（数量 4，一次读回 X+Y）"],["相对/绝对零点","0x000B（0x0000 绝对零点，0x0001 相对零点）"],["通讯速率设置","0x000C（0x0001=2400，0x0002=4800，0x0003=9600，0x0004=19200，0x0000=115200）"],["模块地址设置","0x000D（出厂默认 0x01，总线地址范围 00~FE）"],["掉电保存","update flash 写入 0x000F；参数设置后未发保存命令，断电重启将丢失"]],"notes":["本传感器将两帧数据帧之间的时间间隔提高到大于 10ms，请在每帧数据之间至少留下 10ms 间隔。","通讯时序：主机发送命令 → 10ms 空闲 → 从机回命令 → 10ms 空闲 → 主机发送命令。","如需在 Modbus 协议规定的 3.5 个字节时间内完成收发，请将通讯速率提高到 115200。","修改通讯速率或模块地址后，应立即发送掉电保存指令，否则重新上电后设置会丢失。"]}},{"m":"MDR-3628T-I","t":"高精度电流输出型倾角传感器","d":"双轴测量，精度 0.005°，4-20mA 电流输出。","img":"https://www.fleo.cn/uploads/gallery/20261010_6aca04e722f13.png","g":"高精度 0.005°","head":"高精度倾角传感器","sub":"精度 0.005°，严苛场景适用","axis":"双轴","prec":"0.005°","out":"4-20mA 电流输出","app":"","sk":"3628T","single":false,"ovr":"新一代工业级 MEMS 型双轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[["测量范围","±5° / ±10° / ±20° / ±30°（按型号后缀 I5 / I10 / I20 / I30 区分）"],["测量轴","X、Y 轴"],["绝对精度","0.005 °"],["分辨率","0.0007 °"],["长期稳定性","< 0.002 °（@25℃）"],["零点温度系数","±0.0008 °/°C（-40~85℃）"],["监测频率","100 Hz"],["工作电压","DC 5V 或 DC 9~36V"],["工作电流","45 mA（DC 12V 条件下）"],["通讯接口","默认 MODBUS（RS485），其它可选"],["平均工作时间","≥ 5000 小时/次"],["抗冲击","> 20000g，0.5ms，3 次/轴"],["抗震动","10grms，10~1000Hz"],["绝缘电阻","≥ 100MΩ"],["防水等级","IP67 或 IP68"],["电缆线","默认 4 芯屏蔽电缆线 1.5 米"],["重量","180g（不含包装盒）"]],"wiring":{"header":["线色","序号","RS232","RS485","TTL"],"rows":[["红色","1","VCC","VCC","VCC"],["黑色","2","GND","GND","GND"],["黄色","3","TXD","(A、D+)","TXD"],["绿色","4","RXD","(B、D-)","RXD"]],"note":"出厂默认 4 芯屏蔽电缆线 1.5 米，端子定义以本表为准；接线前请确认供电极性，避免带电插拔。"},"size":{"model":"L90 × W40 × H27 mm","mount":"4×M4 螺孔","note":"不同安装面结构会有对应尺寸版本，下单前请与技术人员确认孔位与结构版本。"},"mount":["被测量安装面必须平整，安装面不平会导致测量数据不准确。","安装传感器时，轴 A 应与被测角度旋转轴线平行，否则会带来测量误差。","水平向上/向下、竖直向上/向下共四种安装姿态，需对应确认 X/Y 轴正负方向，装反会导致读数符号相反。","安装完成后建议先用标准角度校验一次，确认读数方向与量程符合预期再接入系统。"],"proto":{"summary":"默认 MODBUS RTU（RS485）通讯协议，8 位数据位、1 位停止位、无校验，默认波特率 9600。","rows":[["数据格式","8 位数据位，1 位停止位，无校验，默认速率 9600"],["角度读取功能码","0x03 读（0x06 写）"],["X 轴角度寄存器","0x0001（数量 2，32 位浮点，IEEE754）"],["Y 轴角度寄存器","0x0002（数量 2，32 位浮点，IEEE754）"],["X/Y 双轴寄存器","0x0001（数量 4，一次读回 X+Y）"],["相对/绝对零点","0x000B（0x0000 绝对零点，0x0001 相对零点）"],["通讯速率设置","0x000C（0x0001=2400，0x0002=4800，0x0003=9600，0x0004=19200，0x0000=115200）"],["模块地址设置","0x000D（出厂默认 0x01，总线地址范围 00~FE）"],["掉电保存","update flash 写入 0x000F；参数设置后未发保存命令，断电重启将丢失"]],"notes":["本传感器将两帧数据帧之间的时间间隔提高到大于 10ms，请在每帧数据之间至少留下 10ms 间隔。","通讯时序：主机发送命令 → 10ms 空闲 → 从机回命令 → 10ms 空闲 → 主机发送命令。","如需在 Modbus 协议规定的 3.5 个字节时间内完成收发，请将通讯速率提高到 115200。","修改通讯速率或模块地址后，应立即发送掉电保存指令，否则重新上电后设置会丢失。"]}},{"m":"MDR-3618T-V","t":"高精度电压输出型倾角传感器（单轴）","d":"单轴测量，精度 0.005°，电压输出，适合高精度单向监测。","img":"https://www.fleo.cn/uploads/gallery/20261010_6aca04e71e5d8.png","g":"高精度 0.005°","head":"高精度倾角传感器","sub":"精度 0.005°，严苛场景适用","axis":"单轴","prec":"0.005°","out":"电压输出","app":"适合高精度单向监测。","sk":"3628T","single":true,"ovr":"新一代工业级 MEMS 型单轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[["测量范围","±5° / ±10° / ±20° / ±30°（按型号后缀 I5 / I10 / I20 / I30 区分）"],["测量轴","X 轴（单轴测量）"],["绝对精度","0.005 °"],["分辨率","0.0007 °"],["长期稳定性","< 0.002 °（@25℃）"],["零点温度系数","±0.0008 °/°C（-40~85℃）"],["监测频率","100 Hz"],["工作电压","DC 5V 或 DC 9~36V"],["工作电流","45 mA（DC 12V 条件下）"],["通讯接口","默认 MODBUS（RS485），其它可选"],["平均工作时间","≥ 5000 小时/次"],["抗冲击","> 20000g，0.5ms，3 次/轴"],["抗震动","10grms，10~1000Hz"],["绝缘电阻","≥ 100MΩ"],["防水等级","IP67 或 IP68"],["电缆线","默认 4 芯屏蔽电缆线 1.5 米"],["重量","180g（不含包装盒）"]],"wiring":{"header":["线色","序号","RS232","RS485","TTL"],"rows":[["红色","1","VCC","VCC","VCC"],["黑色","2","GND","GND","GND"],["黄色","3","TXD","(A、D+)","TXD"],["绿色","4","RXD","(B、D-)","RXD"]],"note":"出厂默认 4 芯屏蔽电缆线 1.5 米，端子定义以本表为准；接线前请确认供电极性，避免带电插拔。"},"size":{"model":"L90 × W40 × H27 mm","mount":"4×M4 螺孔","note":"不同安装面结构会有对应尺寸版本，下单前请与技术人员确认孔位与结构版本。"},"mount":["被测量安装面必须平整，安装面不平会导致测量数据不准确。","安装传感器时，轴 A 应与被测角度旋转轴线平行，否则会带来测量误差。","水平向上/向下、竖直向上/向下共四种安装姿态，需对应确认 X/Y 轴正负方向，装反会导致读数符号相反。","安装完成后建议先用标准角度校验一次，确认读数方向与量程符合预期再接入系统。"],"proto":null},{"m":"MDR-3618T-D","t":"高精度数字型倾角传感器（单轴）","d":"单轴测量，精度 0.005°，数字输出，便于接入采集系统。","img":"https://www.fleo.cn/uploads/gallery/20261010_6aca04e71fb5e.png","g":"高精度 0.005°","head":"高精度倾角传感器","sub":"精度 0.005°，严苛场景适用","axis":"单轴","prec":"0.005°","out":"数字输出","app":"","sk":"3628T","single":true,"ovr":"新一代工业级 MEMS 型单轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[["测量范围","±5° / ±10° / ±20° / ±30°（按型号后缀 I5 / I10 / I20 / I30 区分）"],["测量轴","X 轴（单轴测量）"],["绝对精度","0.005 °"],["分辨率","0.0007 °"],["长期稳定性","< 0.002 °（@25℃）"],["零点温度系数","±0.0008 °/°C（-40~85℃）"],["监测频率","100 Hz"],["工作电压","DC 5V 或 DC 9~36V"],["工作电流","45 mA（DC 12V 条件下）"],["通讯接口","默认 MODBUS（RS485），其它可选"],["平均工作时间","≥ 5000 小时/次"],["抗冲击","> 20000g，0.5ms，3 次/轴"],["抗震动","10grms，10~1000Hz"],["绝缘电阻","≥ 100MΩ"],["防水等级","IP67 或 IP68"],["电缆线","默认 4 芯屏蔽电缆线 1.5 米"],["重量","180g（不含包装盒）"]],"wiring":{"header":["线色","序号","RS232","RS485","TTL"],"rows":[["红色","1","VCC","VCC","VCC"],["黑色","2","GND","GND","GND"],["黄色","3","TXD","(A、D+)","TXD"],["绿色","4","RXD","(B、D-)","RXD"]],"note":"出厂默认 4 芯屏蔽电缆线 1.5 米，端子定义以本表为准；接线前请确认供电极性，避免带电插拔。"},"size":{"model":"L90 × W40 × H27 mm","mount":"4×M4 螺孔","note":"不同安装面结构会有对应尺寸版本，下单前请与技术人员确认孔位与结构版本。"},"mount":["被测量安装面必须平整，安装面不平会导致测量数据不准确。","安装传感器时，轴 A 应与被测角度旋转轴线平行，否则会带来测量误差。","水平向上/向下、竖直向上/向下共四种安装姿态，需对应确认 X/Y 轴正负方向，装反会导致读数符号相反。","安装完成后建议先用标准角度校验一次，确认读数方向与量程符合预期再接入系统。"],"proto":null},{"m":"MDR-3618T-M","t":"高精度 MODBUS 型倾角传感器（单轴）","d":"单轴测量，精度 0.005°，支持 Modbus-RTU 协议。","img":"https://www.fleo.cn/uploads/gallery/20261010_6aca04e720ab5.png","g":"高精度 0.005°","head":"高精度倾角传感器","sub":"精度 0.005°，严苛场景适用","axis":"单轴","prec":"0.005°","out":"Modbus-RTU 协议","app":"","sk":"3628T","single":true,"ovr":"新一代工业级 MEMS 型单轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[["测量范围","±5° / ±10° / ±20° / ±30°（按型号后缀 I5 / I10 / I20 / I30 区分）"],["测量轴","X 轴（单轴测量）"],["绝对精度","0.005 °"],["分辨率","0.0007 °"],["长期稳定性","< 0.002 °（@25℃）"],["零点温度系数","±0.0008 °/°C（-40~85℃）"],["监测频率","100 Hz"],["工作电压","DC 5V 或 DC 9~36V"],["工作电流","45 mA（DC 12V 条件下）"],["通讯接口","默认 MODBUS（RS485），其它可选"],["平均工作时间","≥ 5000 小时/次"],["抗冲击","> 20000g，0.5ms，3 次/轴"],["抗震动","10grms，10~1000Hz"],["绝缘电阻","≥ 100MΩ"],["防水等级","IP67 或 IP68"],["电缆线","默认 4 芯屏蔽电缆线 1.5 米"],["重量","180g（不含包装盒）"]],"wiring":{"header":["线色","序号","RS232","RS485","TTL"],"rows":[["红色","1","VCC","VCC","VCC"],["黑色","2","GND","GND","GND"],["黄色","3","TXD","(A、D+)","TXD"],["绿色","4","RXD","(B、D-)","RXD"]],"note":"出厂默认 4 芯屏蔽电缆线 1.5 米，端子定义以本表为准；接线前请确认供电极性，避免带电插拔。"},"size":{"model":"L90 × W40 × H27 mm","mount":"4×M4 螺孔","note":"不同安装面结构会有对应尺寸版本，下单前请与技术人员确认孔位与结构版本。"},"mount":["被测量安装面必须平整，安装面不平会导致测量数据不准确。","安装传感器时，轴 A 应与被测角度旋转轴线平行，否则会带来测量误差。","水平向上/向下、竖直向上/向下共四种安装姿态，需对应确认 X/Y 轴正负方向，装反会导致读数符号相反。","安装完成后建议先用标准角度校验一次，确认读数方向与量程符合预期再接入系统。"],"proto":null},{"m":"MDR-3618T-I","t":"高精度电流输出型倾角传感器（单轴）","d":"单轴测量，精度 0.005°，4-20mA 电流输出。","img":"https://www.fleo.cn/uploads/gallery/20261010_6aca04e721b6a.png","g":"高精度 0.005°","head":"高精度倾角传感器","sub":"精度 0.005°，严苛场景适用","axis":"单轴","prec":"0.005°","out":"4-20mA 电流输出","app":"","sk":"3628T","single":true,"ovr":"新一代工业级 MEMS 型单轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[["测量范围","±5° / ±10° / ±20° / ±30°（按型号后缀 I5 / I10 / I20 / I30 区分）"],["测量轴","X 轴（单轴测量）"],["绝对精度","0.005 °"],["分辨率","0.0007 °"],["长期稳定性","< 0.002 °（@25℃）"],["零点温度系数","±0.0008 °/°C（-40~85℃）"],["监测频率","100 Hz"],["工作电压","DC 5V 或 DC 9~36V"],["工作电流","45 mA（DC 12V 条件下）"],["通讯接口","默认 MODBUS（RS485），其它可选"],["平均工作时间","≥ 5000 小时/次"],["抗冲击","> 20000g，0.5ms，3 次/轴"],["抗震动","10grms，10~1000Hz"],["绝缘电阻","≥ 100MΩ"],["防水等级","IP67 或 IP68"],["电缆线","默认 4 芯屏蔽电缆线 1.5 米"],["重量","180g（不含包装盒）"]],"wiring":{"header":["线色","序号","RS232","RS485","TTL"],"rows":[["红色","1","VCC","VCC","VCC"],["黑色","2","GND","GND","GND"],["黄色","3","TXD","(A、D+)","TXD"],["绿色","4","RXD","(B、D-)","RXD"]],"note":"出厂默认 4 芯屏蔽电缆线 1.5 米，端子定义以本表为准；接线前请确认供电极性，避免带电插拔。"},"size":{"model":"L90 × W40 × H27 mm","mount":"4×M4 螺孔","note":"不同安装面结构会有对应尺寸版本，下单前请与技术人员确认孔位与结构版本。"},"mount":["被测量安装面必须平整，安装面不平会导致测量数据不准确。","安装传感器时，轴 A 应与被测角度旋转轴线平行，否则会带来测量误差。","水平向上/向下、竖直向上/向下共四种安装姿态，需对应确认 X/Y 轴正负方向，装反会导致读数符号相反。","安装完成后建议先用标准角度校验一次，确认读数方向与量程符合预期再接入系统。"],"proto":null},{"m":"MDR-3629T","t":"双轴超高精度倾角传感器","d":"双轴超高精度倾角传感器，精度 0.001°，德克西尔主力型号，适用于结构长期形变监测。","img":"https://www.fleo.cn/uploads/gallery/20261010_6aca04e71e5d8.png","g":"超高精度 0.001°","head":"超高精度倾角传感器","sub":"精度 0.001°，3629 系列主力","axis":"双轴","prec":"0.001°","out":"","app":"适用于结构长期形变监测。","sk":"3629T","single":false,"ovr":"新一代工业级 MEMS 型双轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[["测量范围","±5° / ±10° / ±20° / ±30°（按型号后缀 I5 / I10 / I20 / I30 区分）"],["测量轴","X、Y 轴"],["绝对精度","0.001 °（±5° / ±10° 量程）；0.002 °（±20°）；0.003 °（±30°）"],["分辨率","0.0005 °"],["长期稳定性","< 0.001 °（@25℃）"],["零点温度系数","±0.0008 °/°C（-40~85℃）"],["监测频率","100 Hz"],["工作电压","DC 5V 或 DC 9~36V"],["工作电流","45 mA（DC 12V 条件下）"],["通讯接口","默认 MODBUS（RS485），其它可选"],["平均工作时间","≥ 5000 小时/次"],["抗冲击","> 20000g，0.5ms，3 次/轴"],["抗震动","10grms，10~1000Hz"],["绝缘电阻","≥ 100MΩ"],["防水等级","IP67 或 IP68"],["电缆线","默认 4 芯屏蔽电缆线 1.5 米"],["重量","180g（不含包装盒）"]],"wiring":{"header":["线色","序号","RS232","RS485","TTL"],"rows":[["红色","1","VCC","VCC","VCC"],["黑色","2","GND","GND","GND"],["黄色","3","TXD","(A、D+)","TXD"],["绿色","4","RXD","(B、D-)","RXD"]],"note":"出厂默认 4 芯屏蔽电缆线 1.5 米，端子定义以本表为准；接线前请确认供电极性，避免带电插拔。"},"size":{"model":"L90 × W40 × H27 mm","mount":"4×M4 螺孔","note":"不同安装面结构会有对应尺寸版本，下单前请与技术人员确认孔位与结构版本。"},"mount":["被测量安装面必须平整，安装面不平会导致测量数据不准确。","安装传感器时，轴 A 应与被测角度旋转轴线平行，否则会带来测量误差。","水平向上/向下、竖直向上/向下共四种安装姿态，需对应确认 X/Y 轴正负方向，装反会导致读数符号相反。","安装完成后建议先用标准角度校验一次，确认读数方向与量程符合预期再接入系统。"],"proto":{"summary":"默认 MODBUS RTU（RS485）通讯协议，8 位数据位、1 位停止位、无校验，默认波特率 9600。","rows":[["数据格式","8 位数据位，1 位停止位，无校验，默认速率 9600"],["角度读取功能码","0x03 读（0x06 写）"],["X 轴角度寄存器","0x0001（数量 2，32 位浮点，IEEE754）"],["Y 轴角度寄存器","0x0002（数量 2，32 位浮点，IEEE754）"],["X/Y 双轴寄存器","0x0001（数量 4，一次读回 X+Y）"],["相对/绝对零点","0x000B（0x0000 绝对零点，0x0001 相对零点）"],["通讯速率设置","0x000C（0x0001=2400，0x0002=4800，0x0003=9600，0x0004=19200，0x0000=115200）"],["模块地址设置","0x000D（出厂默认 0x01，总线地址范围 00~FE）"],["掉电保存","update flash 写入 0x000F；参数设置后未发保存命令，断电重启将丢失"]],"notes":["本传感器将两帧数据帧之间的时间间隔提高到大于 10ms，请在每帧数据之间至少留下 10ms 间隔。","通讯时序：主机发送命令 → 10ms 空闲 → 从机回命令 → 10ms 空闲 → 主机发送命令。","如需在 Modbus 协议规定的 3.5 个字节时间内完成收发，请将通讯速率提高到 115200。","修改通讯速率或模块地址后，应立即发送掉电保存指令，否则重新上电后设置会丢失。"]}},{"m":"MDR-3629T-D","t":"双轴超高精度数字型倾角传感器","d":"双轴测量，精度 0.001°，数字输出，超高精度主力系列，便于接入采集系统。","img":"https://www.fleo.cn/uploads/gallery/20261010_6aca04e71fb5e.png","g":"超高精度 0.001°","head":"超高精度倾角传感器","sub":"精度 0.001°，3629 系列主力","axis":"双轴","prec":"0.001°","out":"数字输出","app":"","sk":"3629T","single":false,"ovr":"新一代工业级 MEMS 型双轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[["测量范围","±5° / ±10° / ±20° / ±30°（按型号后缀 I5 / I10 / I20 / I30 区分）"],["测量轴","X、Y 轴"],["绝对精度","0.001 °（±5° / ±10° 量程）；0.002 °（±20°）；0.003 °（±30°）"],["分辨率","0.0005 °"],["长期稳定性","< 0.001 °（@25℃）"],["零点温度系数","±0.0008 °/°C（-40~85℃）"],["监测频率","100 Hz"],["工作电压","DC 5V 或 DC 9~36V"],["工作电流","45 mA（DC 12V 条件下）"],["通讯接口","默认 MODBUS（RS485），其它可选"],["平均工作时间","≥ 5000 小时/次"],["抗冲击","> 20000g，0.5ms，3 次/轴"],["抗震动","10grms，10~1000Hz"],["绝缘电阻","≥ 100MΩ"],["防水等级","IP67 或 IP68"],["电缆线","默认 4 芯屏蔽电缆线 1.5 米"],["重量","180g（不含包装盒）"]],"wiring":{"header":["线色","序号","RS232","RS485","TTL"],"rows":[["红色","1","VCC","VCC","VCC"],["黑色","2","GND","GND","GND"],["黄色","3","TXD","(A、D+)","TXD"],["绿色","4","RXD","(B、D-)","RXD"]],"note":"出厂默认 4 芯屏蔽电缆线 1.5 米，端子定义以本表为准；接线前请确认供电极性，避免带电插拔。"},"size":{"model":"L90 × W40 × H27 mm","mount":"4×M4 螺孔","note":"不同安装面结构会有对应尺寸版本，下单前请与技术人员确认孔位与结构版本。"},"mount":["被测量安装面必须平整，安装面不平会导致测量数据不准确。","安装传感器时，轴 A 应与被测角度旋转轴线平行，否则会带来测量误差。","水平向上/向下、竖直向上/向下共四种安装姿态，需对应确认 X/Y 轴正负方向，装反会导致读数符号相反。","安装完成后建议先用标准角度校验一次，确认读数方向与量程符合预期再接入系统。"],"proto":{"summary":"默认 MODBUS RTU（RS485）通讯协议，8 位数据位、1 位停止位、无校验，默认波特率 9600。","rows":[["数据格式","8 位数据位，1 位停止位，无校验，默认速率 9600"],["角度读取功能码","0x03 读（0x06 写）"],["X 轴角度寄存器","0x0001（数量 2，32 位浮点，IEEE754）"],["Y 轴角度寄存器","0x0002（数量 2，32 位浮点，IEEE754）"],["X/Y 双轴寄存器","0x0001（数量 4，一次读回 X+Y）"],["相对/绝对零点","0x000B（0x0000 绝对零点，0x0001 相对零点）"],["通讯速率设置","0x000C（0x0001=2400，0x0002=4800，0x0003=9600，0x0004=19200，0x0000=115200）"],["模块地址设置","0x000D（出厂默认 0x01，总线地址范围 00~FE）"],["掉电保存","update flash 写入 0x000F；参数设置后未发保存命令，断电重启将丢失"]],"notes":["本传感器将两帧数据帧之间的时间间隔提高到大于 10ms，请在每帧数据之间至少留下 10ms 间隔。","通讯时序：主机发送命令 → 10ms 空闲 → 从机回命令 → 10ms 空闲 → 主机发送命令。","如需在 Modbus 协议规定的 3.5 个字节时间内完成收发，请将通讯速率提高到 115200。","修改通讯速率或模块地址后，应立即发送掉电保存指令，否则重新上电后设置会丢失。"]}},{"m":"MDR-3629T-M","t":"双轴超高精度 MODBUS 型倾角传感器","d":"双轴测量，精度 0.001°，支持 Modbus-RTU 协议，利于多节点组网。","img":"https://www.fleo.cn/uploads/gallery/20261010_6aca04e720ab5.png","g":"超高精度 0.001°","head":"超高精度倾角传感器","sub":"精度 0.001°，3629 系列主力","axis":"双轴","prec":"0.001°","out":"Modbus-RTU 协议","app":"","sk":"3629T","single":false,"ovr":"新一代工业级 MEMS 型双轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[["测量范围","±5° / ±10° / ±20° / ±30°（按型号后缀 I5 / I10 / I20 / I30 区分）"],["测量轴","X、Y 轴"],["绝对精度","0.001 °（±5° / ±10° 量程）；0.002 °（±20°）；0.003 °（±30°）"],["分辨率","0.0005 °"],["长期稳定性","< 0.001 °（@25℃）"],["零点温度系数","±0.0008 °/°C（-40~85℃）"],["监测频率","100 Hz"],["工作电压","DC 5V 或 DC 9~36V"],["工作电流","45 mA（DC 12V 条件下）"],["通讯接口","默认 MODBUS（RS485），其它可选"],["平均工作时间","≥ 5000 小时/次"],["抗冲击","> 20000g，0.5ms，3 次/轴"],["抗震动","10grms，10~1000Hz"],["绝缘电阻","≥ 100MΩ"],["防水等级","IP67 或 IP68"],["电缆线","默认 4 芯屏蔽电缆线 1.5 米"],["重量","180g（不含包装盒）"]],"wiring":{"header":["线色","序号","RS232","RS485","TTL"],"rows":[["红色","1","VCC","VCC","VCC"],["黑色","2","GND","GND","GND"],["黄色","3","TXD","(A、D+)","TXD"],["绿色","4","RXD","(B、D-)","RXD"]],"note":"出厂默认 4 芯屏蔽电缆线 1.5 米，端子定义以本表为准；接线前请确认供电极性，避免带电插拔。"},"size":{"model":"L90 × W40 × H27 mm","mount":"4×M4 螺孔","note":"不同安装面结构会有对应尺寸版本，下单前请与技术人员确认孔位与结构版本。"},"mount":["被测量安装面必须平整，安装面不平会导致测量数据不准确。","安装传感器时，轴 A 应与被测角度旋转轴线平行，否则会带来测量误差。","水平向上/向下、竖直向上/向下共四种安装姿态，需对应确认 X/Y 轴正负方向，装反会导致读数符号相反。","安装完成后建议先用标准角度校验一次，确认读数方向与量程符合预期再接入系统。"],"proto":{"summary":"默认 MODBUS RTU（RS485）通讯协议，8 位数据位、1 位停止位、无校验，默认波特率 9600。","rows":[["数据格式","8 位数据位，1 位停止位，无校验，默认速率 9600"],["角度读取功能码","0x03 读（0x06 写）"],["X 轴角度寄存器","0x0001（数量 2，32 位浮点，IEEE754）"],["Y 轴角度寄存器","0x0002（数量 2，32 位浮点，IEEE754）"],["X/Y 双轴寄存器","0x0001（数量 4，一次读回 X+Y）"],["相对/绝对零点","0x000B（0x0000 绝对零点，0x0001 相对零点）"],["通讯速率设置","0x000C（0x0001=2400，0x0002=4800，0x0003=9600，0x0004=19200，0x0000=115200）"],["模块地址设置","0x000D（出厂默认 0x01，总线地址范围 00~FE）"],["掉电保存","update flash 写入 0x000F；参数设置后未发保存命令，断电重启将丢失"]],"notes":["本传感器将两帧数据帧之间的时间间隔提高到大于 10ms，请在每帧数据之间至少留下 10ms 间隔。","通讯时序：主机发送命令 → 10ms 空闲 → 从机回命令 → 10ms 空闲 → 主机发送命令。","如需在 Modbus 协议规定的 3.5 个字节时间内完成收发，请将通讯速率提高到 115200。","修改通讯速率或模块地址后，应立即发送掉电保存指令，否则重新上电后设置会丢失。"]}},{"m":"MDR-3629T-I","t":"双轴超高精度电流输出型倾角传感器","d":"双轴测量，精度 0.001°，4-20mA 电流输出，兼容老旧仪表柜。","img":"https://www.fleo.cn/uploads/gallery/20261010_6aca04e721b6a.png","g":"超高精度 0.001°","head":"超高精度倾角传感器","sub":"精度 0.001°，3629 系列主力","axis":"双轴","prec":"0.001°","out":"4-20mA 电流输出","app":"","sk":"3629T","single":false,"ovr":"新一代工业级 MEMS 型双轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[["测量范围","±5° / ±10° / ±20° / ±30°（按型号后缀 I5 / I10 / I20 / I30 区分）"],["测量轴","X、Y 轴"],["绝对精度","0.001 °（±5° / ±10° 量程）；0.002 °（±20°）；0.003 °（±30°）"],["分辨率","0.0005 °"],["长期稳定性","< 0.001 °（@25℃）"],["零点温度系数","±0.0008 °/°C（-40~85℃）"],["监测频率","100 Hz"],["工作电压","DC 5V 或 DC 9~36V"],["工作电流","45 mA（DC 12V 条件下）"],["通讯接口","默认 MODBUS（RS485），其它可选"],["平均工作时间","≥ 5000 小时/次"],["抗冲击","> 20000g，0.5ms，3 次/轴"],["抗震动","10grms，10~1000Hz"],["绝缘电阻","≥ 100MΩ"],["防水等级","IP67 或 IP68"],["电缆线","默认 4 芯屏蔽电缆线 1.5 米"],["重量","180g（不含包装盒）"]],"wiring":{"header":["线色","序号","RS232","RS485","TTL"],"rows":[["红色","1","VCC","VCC","VCC"],["黑色","2","GND","GND","GND"],["黄色","3","TXD","(A、D+)","TXD"],["绿色","4","RXD","(B、D-)","RXD"]],"note":"出厂默认 4 芯屏蔽电缆线 1.5 米，端子定义以本表为准；接线前请确认供电极性，避免带电插拔。"},"size":{"model":"L90 × W40 × H27 mm","mount":"4×M4 螺孔","note":"不同安装面结构会有对应尺寸版本，下单前请与技术人员确认孔位与结构版本。"},"mount":["被测量安装面必须平整，安装面不平会导致测量数据不准确。","安装传感器时，轴 A 应与被测角度旋转轴线平行，否则会带来测量误差。","水平向上/向下、竖直向上/向下共四种安装姿态，需对应确认 X/Y 轴正负方向，装反会导致读数符号相反。","安装完成后建议先用标准角度校验一次，确认读数方向与量程符合预期再接入系统。"],"proto":{"summary":"默认 MODBUS RTU（RS485）通讯协议，8 位数据位、1 位停止位、无校验，默认波特率 9600。","rows":[["数据格式","8 位数据位，1 位停止位，无校验，默认速率 9600"],["角度读取功能码","0x03 读（0x06 写）"],["X 轴角度寄存器","0x0001（数量 2，32 位浮点，IEEE754）"],["Y 轴角度寄存器","0x0002（数量 2，32 位浮点，IEEE754）"],["X/Y 双轴寄存器","0x0001（数量 4，一次读回 X+Y）"],["相对/绝对零点","0x000B（0x0000 绝对零点，0x0001 相对零点）"],["通讯速率设置","0x000C（0x0001=2400，0x0002=4800，0x0003=9600，0x0004=19200，0x0000=115200）"],["模块地址设置","0x000D（出厂默认 0x01，总线地址范围 00~FE）"],["掉电保存","update flash 写入 0x000F；参数设置后未发保存命令，断电重启将丢失"]],"notes":["本传感器将两帧数据帧之间的时间间隔提高到大于 10ms，请在每帧数据之间至少留下 10ms 间隔。","通讯时序：主机发送命令 → 10ms 空闲 → 从机回命令 → 10ms 空闲 → 主机发送命令。","如需在 Modbus 协议规定的 3.5 个字节时间内完成收发，请将通讯速率提高到 115200。","修改通讯速率或模块地址后，应立即发送掉电保存指令，否则重新上电后设置会丢失。"]}},{"m":"MDR-3619T-V","t":"超高精度电压输出型倾角传感器（单轴）","d":"单轴测量，精度 0.001°，电压输出，超高精度单向监测。","img":"https://www.fleo.cn/uploads/gallery/20261010_6aca04e71fb5e.png","g":"超高精度 0.001°","head":"超高精度倾角传感器","sub":"精度 0.001°，3629 系列主力","axis":"单轴","prec":"0.001°","out":"电压输出","app":"","sk":"3629T","single":true,"ovr":"新一代工业级 MEMS 型单轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[["测量范围","±5° / ±10° / ±20° / ±30°（按型号后缀 I5 / I10 / I20 / I30 区分）"],["测量轴","X 轴（单轴测量）"],["绝对精度","0.001 °（±5° / ±10° 量程）；0.002 °（±20°）；0.003 °（±30°）"],["分辨率","0.0005 °"],["长期稳定性","< 0.001 °（@25℃）"],["零点温度系数","±0.0008 °/°C（-40~85℃）"],["监测频率","100 Hz"],["工作电压","DC 5V 或 DC 9~36V"],["工作电流","45 mA（DC 12V 条件下）"],["通讯接口","默认 MODBUS（RS485），其它可选"],["平均工作时间","≥ 5000 小时/次"],["抗冲击","> 20000g，0.5ms，3 次/轴"],["抗震动","10grms，10~1000Hz"],["绝缘电阻","≥ 100MΩ"],["防水等级","IP67 或 IP68"],["电缆线","默认 4 芯屏蔽电缆线 1.5 米"],["重量","180g（不含包装盒）"]],"wiring":{"header":["线色","序号","RS232","RS485","TTL"],"rows":[["红色","1","VCC","VCC","VCC"],["黑色","2","GND","GND","GND"],["黄色","3","TXD","(A、D+)","TXD"],["绿色","4","RXD","(B、D-)","RXD"]],"note":"出厂默认 4 芯屏蔽电缆线 1.5 米，端子定义以本表为准；接线前请确认供电极性，避免带电插拔。"},"size":{"model":"L90 × W40 × H27 mm","mount":"4×M4 螺孔","note":"不同安装面结构会有对应尺寸版本，下单前请与技术人员确认孔位与结构版本。"},"mount":["被测量安装面必须平整，安装面不平会导致测量数据不准确。","安装传感器时，轴 A 应与被测角度旋转轴线平行，否则会带来测量误差。","水平向上/向下、竖直向上/向下共四种安装姿态，需对应确认 X/Y 轴正负方向，装反会导致读数符号相反。","安装完成后建议先用标准角度校验一次，确认读数方向与量程符合预期再接入系统。"],"proto":null},{"m":"MDR-3619T-D","t":"超高精度数字型倾角传感器（单轴）","d":"单轴测量，精度 0.001°，数字输出，超高精度单向监测。","img":"https://www.fleo.cn/uploads/gallery/20261010_6aca04e720ab5.png","g":"超高精度 0.001°","head":"超高精度倾角传感器","sub":"精度 0.001°，3629 系列主力","axis":"单轴","prec":"0.001°","out":"数字输出","app":"","sk":"3629T","single":true,"ovr":"新一代工业级 MEMS 型单轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[["测量范围","±5° / ±10° / ±20° / ±30°（按型号后缀 I5 / I10 / I20 / I30 区分）"],["测量轴","X 轴（单轴测量）"],["绝对精度","0.001 °（±5° / ±10° 量程）；0.002 °（±20°）；0.003 °（±30°）"],["分辨率","0.0005 °"],["长期稳定性","< 0.001 °（@25℃）"],["零点温度系数","±0.0008 °/°C（-40~85℃）"],["监测频率","100 Hz"],["工作电压","DC 5V 或 DC 9~36V"],["工作电流","45 mA（DC 12V 条件下）"],["通讯接口","默认 MODBUS（RS485），其它可选"],["平均工作时间","≥ 5000 小时/次"],["抗冲击","> 20000g，0.5ms，3 次/轴"],["抗震动","10grms，10~1000Hz"],["绝缘电阻","≥ 100MΩ"],["防水等级","IP67 或 IP68"],["电缆线","默认 4 芯屏蔽电缆线 1.5 米"],["重量","180g（不含包装盒）"]],"wiring":{"header":["线色","序号","RS232","RS485","TTL"],"rows":[["红色","1","VCC","VCC","VCC"],["黑色","2","GND","GND","GND"],["黄色","3","TXD","(A、D+)","TXD"],["绿色","4","RXD","(B、D-)","RXD"]],"note":"出厂默认 4 芯屏蔽电缆线 1.5 米，端子定义以本表为准；接线前请确认供电极性，避免带电插拔。"},"size":{"model":"L90 × W40 × H27 mm","mount":"4×M4 螺孔","note":"不同安装面结构会有对应尺寸版本，下单前请与技术人员确认孔位与结构版本。"},"mount":["被测量安装面必须平整，安装面不平会导致测量数据不准确。","安装传感器时，轴 A 应与被测角度旋转轴线平行，否则会带来测量误差。","水平向上/向下、竖直向上/向下共四种安装姿态，需对应确认 X/Y 轴正负方向，装反会导致读数符号相反。","安装完成后建议先用标准角度校验一次，确认读数方向与量程符合预期再接入系统。"],"proto":null},{"m":"MDR-3619T-M","t":"超高精度 MODBUS 型倾角传感器（单轴）","d":"单轴测量，精度 0.001°，支持 Modbus-RTU 协议。","img":"https://www.fleo.cn/uploads/gallery/20261010_6aca04e721b6a.png","g":"超高精度 0.001°","head":"超高精度倾角传感器","sub":"精度 0.001°，3629 系列主力","axis":"单轴","prec":"0.001°","out":"Modbus-RTU 协议","app":"","sk":"3629T","single":true,"ovr":"新一代工业级 MEMS 型单轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[["测量范围","±5° / ±10° / ±20° / ±30°（按型号后缀 I5 / I10 / I20 / I30 区分）"],["测量轴","X 轴（单轴测量）"],["绝对精度","0.001 °（±5° / ±10° 量程）；0.002 °（±20°）；0.003 °（±30°）"],["分辨率","0.0005 °"],["长期稳定性","< 0.001 °（@25℃）"],["零点温度系数","±0.0008 °/°C（-40~85℃）"],["监测频率","100 Hz"],["工作电压","DC 5V 或 DC 9~36V"],["工作电流","45 mA（DC 12V 条件下）"],["通讯接口","默认 MODBUS（RS485），其它可选"],["平均工作时间","≥ 5000 小时/次"],["抗冲击","> 20000g，0.5ms，3 次/轴"],["抗震动","10grms，10~1000Hz"],["绝缘电阻","≥ 100MΩ"],["防水等级","IP67 或 IP68"],["电缆线","默认 4 芯屏蔽电缆线 1.5 米"],["重量","180g（不含包装盒）"]],"wiring":{"header":["线色","序号","RS232","RS485","TTL"],"rows":[["红色","1","VCC","VCC","VCC"],["黑色","2","GND","GND","GND"],["黄色","3","TXD","(A、D+)","TXD"],["绿色","4","RXD","(B、D-)","RXD"]],"note":"出厂默认 4 芯屏蔽电缆线 1.5 米，端子定义以本表为准；接线前请确认供电极性，避免带电插拔。"},"size":{"model":"L90 × W40 × H27 mm","mount":"4×M4 螺孔","note":"不同安装面结构会有对应尺寸版本，下单前请与技术人员确认孔位与结构版本。"},"mount":["被测量安装面必须平整，安装面不平会导致测量数据不准确。","安装传感器时，轴 A 应与被测角度旋转轴线平行，否则会带来测量误差。","水平向上/向下、竖直向上/向下共四种安装姿态，需对应确认 X/Y 轴正负方向，装反会导致读数符号相反。","安装完成后建议先用标准角度校验一次，确认读数方向与量程符合预期再接入系统。"],"proto":null},{"m":"MDR-3619T-I","t":"超高精度电流输出型倾角传感器（单轴）","d":"单轴测量，精度 0.001°，4-20mA 电流输出。","img":"https://www.fleo.cn/uploads/gallery/20261010_6aca04e722f13.png","g":"超高精度 0.001°","head":"超高精度倾角传感器","sub":"精度 0.001°，3629 系列主力","axis":"单轴","prec":"0.001°","out":"4-20mA 电流输出","app":"","sk":"3629T","single":true,"ovr":"新一代工业级 MEMS 型单轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[["测量范围","±5° / ±10° / ±20° / ±30°（按型号后缀 I5 / I10 / I20 / I30 区分）"],["测量轴","X 轴（单轴测量）"],["绝对精度","0.001 °（±5° / ±10° 量程）；0.002 °（±20°）；0.003 °（±30°）"],["分辨率","0.0005 °"],["长期稳定性","< 0.001 °（@25℃）"],["零点温度系数","±0.0008 °/°C（-40~85℃）"],["监测频率","100 Hz"],["工作电压","DC 5V 或 DC 9~36V"],["工作电流","45 mA（DC 12V 条件下）"],["通讯接口","默认 MODBUS（RS485），其它可选"],["平均工作时间","≥ 5000 小时/次"],["抗冲击","> 20000g，0.5ms，3 次/轴"],["抗震动","10grms，10~1000Hz"],["绝缘电阻","≥ 100MΩ"],["防水等级","IP67 或 IP68"],["电缆线","默认 4 芯屏蔽电缆线 1.5 米"],["重量","180g（不含包装盒）"]],"wiring":{"header":["线色","序号","RS232","RS485","TTL"],"rows":[["红色","1","VCC","VCC","VCC"],["黑色","2","GND","GND","GND"],["黄色","3","TXD","(A、D+)","TXD"],["绿色","4","RXD","(B、D-)","RXD"]],"note":"出厂默认 4 芯屏蔽电缆线 1.5 米，端子定义以本表为准；接线前请确认供电极性，避免带电插拔。"},"size":{"model":"L90 × W40 × H27 mm","mount":"4×M4 螺孔","note":"不同安装面结构会有对应尺寸版本，下单前请与技术人员确认孔位与结构版本。"},"mount":["被测量安装面必须平整，安装面不平会导致测量数据不准确。","安装传感器时，轴 A 应与被测角度旋转轴线平行，否则会带来测量误差。","水平向上/向下、竖直向上/向下共四种安装姿态，需对应确认 X/Y 轴正负方向，装反会导致读数符号相反。","安装完成后建议先用标准角度校验一次，确认读数方向与量程符合预期再接入系统。"],"proto":null},{"m":"MDR-3620T","t":"低功耗无线倾角传感器","d":"双轴 · 数字型 · 精度 0.1°，低功耗无线，适合无布线远程监测。","img":"https://www.fleo.cn/uploads/gallery/20261014_6acf931a66223.png","g":"无线倾角仪","head":"低功耗无线倾角仪","sub":"MDR-36x0T 系列 · 无布线 · 电池长续航","axis":"双轴","prec":"0.1°","out":"数字输出","app":"适合无布线远程监测。","sk":null,"single":false,"ovr":"新一代工业级 MEMS 型双轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[],"wiring":null,"size":null,"mount":null,"proto":null},{"m":"MDR-3621T","t":"低功耗无线倾角传感器","d":"双轴 · MODBUS · 精度 0.01°，低功耗无线，适合无布线远程监测。","img":"https://www.fleo.cn/uploads/gallery/20261014_6acf932f2c953.png","g":"无线倾角仪","head":"低功耗无线倾角仪","sub":"MDR-36x0T 系列 · 无布线 · 电池长续航","axis":"双轴","prec":"0.01°","out":"Modbus-RTU 协议","app":"适合无布线远程监测。","sk":null,"single":false,"ovr":"新一代工业级 MEMS 型双轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[],"wiring":null,"size":null,"mount":null,"proto":null},{"m":"MDR-3622T","t":"低功耗无线倾角传感器","d":"双轴 · 数字型 · 精度 0.005°，低功耗无线，适合无布线远程监测。","img":"https://www.fleo.cn/uploads/gallery/20261014_6acf92465d8c0.png","g":"无线倾角仪","head":"低功耗无线倾角仪","sub":"MDR-36x0T 系列 · 无布线 · 电池长续航","axis":"双轴","prec":"0.005°","out":"数字输出","app":"适合无布线远程监测。","sk":null,"single":false,"ovr":"新一代工业级 MEMS 型双轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[],"wiring":null,"size":null,"mount":null,"proto":null},{"m":"MDR-3610T","t":"低功耗无线倾角传感器（单轴）","d":"单轴 · 数字型 · 精度 0.1°，低功耗无线，单向倾斜监测。","img":"https://www.fleo.cn/uploads/gallery/20261014_6acf931a66223.png","g":"无线倾角仪","head":"低功耗无线倾角仪","sub":"MDR-36x0T 系列 · 无布线 · 电池长续航","axis":"单轴","prec":"0.1°","out":"数字输出","app":"","sk":null,"single":false,"ovr":"新一代工业级 MEMS 型双轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[],"wiring":null,"size":null,"mount":null,"proto":null},{"m":"MDR-3611T","t":"低功耗无线倾角传感器（单轴）","d":"单轴 · MODBUS · 精度 0.1°，低功耗无线，单向倾斜监测。","img":"https://www.fleo.cn/uploads/gallery/20261014_6acf932f2c953.png","g":"无线倾角仪","head":"低功耗无线倾角仪","sub":"MDR-36x0T 系列 · 无布线 · 电池长续航","axis":"单轴","prec":"0.1°","out":"Modbus-RTU 协议","app":"","sk":null,"single":false,"ovr":"新一代工业级 MEMS 型双轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[],"wiring":null,"size":null,"mount":null,"proto":null},{"m":"MDR-3612T","t":"低功耗无线倾角传感器（单轴）","d":"单轴 · 数字型 · 精度 0.005°，低功耗无线，单向倾斜监测。","img":"https://www.fleo.cn/uploads/gallery/20261014_6acf92465d8c0.png","g":"无线倾角仪","head":"低功耗无线倾角仪","sub":"MDR-36x0T 系列 · 无布线 · 电池长续航","axis":"单轴","prec":"0.005°","out":"数字输出","app":"","sk":null,"single":false,"ovr":"新一代工业级 MEMS 型双轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[],"wiring":null,"size":null,"mount":null,"proto":null},{"m":"MDR-3620D-1","t":"数显无线倾角传感器","d":"双轴 · 数字型 · 精度 0.1°，内置显示屏，无线传输。","img":"https://www.fleo.cn/uploads/gallery/20261015_6ad037dfe0ce8.png","g":"数显倾角仪","head":"数显倾角仪","sub":"内置显示屏现场直读 · 数显无线(-1) / 数显有线(-2)","axis":"双轴","prec":"0.1°","out":"数字输出 / 无线传输","app":"","sk":null,"single":false,"ovr":"新一代工业级 MEMS 型双轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[],"wiring":null,"size":null,"mount":null,"proto":null},{"m":"MDR-3621D-1","t":"数显无线倾角传感器","d":"双轴 · 数字型 · 精度 0.01°，内置显示屏，无线传输。","img":"https://www.fleo.cn/uploads/gallery/20261015_6ad037dd8eb3e.png","g":"数显倾角仪","head":"数显倾角仪","sub":"内置显示屏现场直读 · 数显无线(-1) / 数显有线(-2)","axis":"双轴","prec":"0.01°","out":"数字输出 / 无线传输","app":"","sk":null,"single":false,"ovr":"新一代工业级 MEMS 型双轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[],"wiring":null,"size":null,"mount":null,"proto":null},{"m":"MDR-3610D-1","t":"数显无线倾角传感器（单轴）","d":"单轴 · 数字型 · 精度 0.1°，内置显示屏，无线传输。","img":"https://www.fleo.cn/uploads/gallery/20261015_6ad037caa8fa0.png","g":"数显倾角仪","head":"数显倾角仪","sub":"内置显示屏现场直读 · 数显无线(-1) / 数显有线(-2)","axis":"单轴","prec":"0.1°","out":"数字输出 / 无线传输","app":"","sk":null,"single":false,"ovr":"新一代工业级 MEMS 型双轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[],"wiring":null,"size":null,"mount":null,"proto":null},{"m":"MDR-3611D-1","t":"数显无线倾角传感器（单轴）","d":"单轴 · 数字型 · 精度 0.01°，内置显示屏，无线传输。","img":"https://www.fleo.cn/uploads/gallery/20261015_6ad037d78dc2e.png","g":"数显倾角仪","head":"数显倾角仪","sub":"内置显示屏现场直读 · 数显无线(-1) / 数显有线(-2)","axis":"单轴","prec":"0.01°","out":"数字输出 / 无线传输","app":"","sk":null,"single":false,"ovr":"新一代工业级 MEMS 型双轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[],"wiring":null,"size":null,"mount":null,"proto":null},{"m":"MDR-3620D-2","t":"数显有线倾角传感器","d":"双轴 · MODBUS · 精度 0.1°，内置显示屏，有线输出。","img":"https://www.fleo.cn/uploads/gallery/20261015_6ad037b93a701.png","g":"数显倾角仪","head":"数显倾角仪","sub":"内置显示屏现场直读 · 数显无线(-1) / 数显有线(-2)","axis":"双轴","prec":"0.1°","out":"Modbus-RTU 协议 / 有线输出","app":"","sk":null,"single":false,"ovr":"新一代工业级 MEMS 型双轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[],"wiring":null,"size":null,"mount":null,"proto":null},{"m":"MDR-3622D-2","t":"数显有线倾角传感器","d":"双轴 · 电流型 · 精度 0.005°，内置显示屏，4-20mA 输出。","img":"https://www.fleo.cn/uploads/gallery/20261015_6ad037b93a701.png","g":"数显倾角仪","head":"数显倾角仪","sub":"内置显示屏现场直读 · 数显无线(-1) / 数显有线(-2)","axis":"双轴","prec":"0.005°","out":"4-20mA 电流输出","app":"","sk":null,"single":false,"ovr":"新一代工业级 MEMS 型双轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[],"wiring":null,"size":null,"mount":null,"proto":null},{"m":"MDR-3610D-2","t":"数显有线倾角传感器（单轴）","d":"单轴 · MODBUS · 精度 0.1°，内置显示屏，有线输出。","img":"https://www.fleo.cn/uploads/gallery/20261015_6ad037b93a701.png","g":"数显倾角仪","head":"数显倾角仪","sub":"内置显示屏现场直读 · 数显无线(-1) / 数显有线(-2)","axis":"单轴","prec":"0.1°","out":"Modbus-RTU 协议 / 有线输出","app":"","sk":null,"single":false,"ovr":"新一代工业级 MEMS 型双轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[],"wiring":null,"size":null,"mount":null,"proto":null},{"m":"MDR-3612D-2","t":"数显有线倾角传感器（单轴）","d":"单轴 · 电流型 · 精度 0.005°，内置显示屏，4-20mA 输出。","img":"https://www.fleo.cn/uploads/gallery/20261015_6ad037b93a701.png","g":"数显倾角仪","head":"数显倾角仪","sub":"内置显示屏现场直读 · 数显无线(-1) / 数显有线(-2)","axis":"单轴","prec":"0.005°","out":"4-20mA 电流输出","app":"","sk":null,"single":false,"ovr":"新一代工业级 MEMS 型双轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","spec":[],"wiring":null,"size":null,"mount":null,"proto":null}],"global":{"overview":"新一代工业级 MEMS 型双轴倾角传感器，采用高解析度微机电系统，实时捕捉重力矢量变化数据，通过最新高解滤波融合算法完成智能补偿与误差修正，输出精准、平滑的角度测量结果。","ovSpec":["全工业级器件方案，覆盖工作区间可达 -40℃~85℃","设备测量精度最高可达 0.001°，分辨率可达 0.0005°","产品默认搭载 Modbus RTU（RS485）通讯，可根据项目需要定制其他输出方式","针对复杂工业场景，设备搭载专属微电子端子板软件电路，有效屏蔽现场各类电磁干扰","保障设备长期连接、稳定不间断运行，大幅提升恶劣工况下的测量可靠性","结构紧凑、体积小巧，接口配置丰富，安装调试简单，极易嵌入各类自动化监测系统与集成设备"],"ovNote":"广泛适用于结构安全监测预警、设备姿态检测、机械振动监测及各类高精度工业测控场景。","scenes":["精密机床水平控制","风机摆振姿态","船舶机械姿态测量","塔杆、风力发电设备","桥梁健康监测","云台调平、高空作业车","边坡等地质灾害领域","各种工程机械角度控制","高精度激光平台","危房、古建筑健康监测"],"std":["倾角传感器生产标准：GB/T191SJ20873-2003 倾斜仪、水平仪通用规范","倾角传感器计量检定校准标准：JJF1119-2004 电子水平仪校准规范","陀螺角度测试标准：QJ2318-92 陀螺角度计测试方法","光纤陀螺仪测试方法：GJB2426A-2004","产品环境试验检测标准：GJB150","电磁干扰试验标准：GB/T17626"],"warranty":{"items":["本产品实行三包服务。","免费保修期限为一年（自购买之日起），请按使用说明书使用；如产品出现故障，请及时与厂家联系。","保修期外维修仅收取成本费。","使用说明书内成品外观由于印刷等原因，可能与实物略有差异，请以实物为准。"],"excl":["未按使用说明书使用引起的设备损坏及故障","自行拆装、改造维修而引起的设备故障及损坏","不可抗拒因素，如水灾、火灾、地震、雷击","使用非本公司原装配件","因使用、维护、保管不当造成损坏（如高温、浸水、腐蚀等）","人为损坏"]}}}